Energy saving and environmental protection, less noise, faster working efficiency than ordinary punches, small footprint, safe and secure operation. Anhui Auto punching machine Which one is good The punching needle is specially designed, and the time for changing the mold is short. Time delay protection circuit. When nobody operates the machine, the time delay protection switch will automatically enter the standby state. If you want to start work, you need to turn on the circuit switch again. The punching machine for handrail shelf of guardrail stairs is widely used in punching stainless steel, aluminum alloy bathroom, color steel, zinc steel guardrails, and is the equipment with fast pipe punching processing at present. Guardrail stair handrail punching machine can be customized to multiple working positions, easy and convenient to disassemble the mold, durable mold, easy for novices to use and so on. Auto punching machine It can debug and punch half hole or full hole at will, with flat punching and accurate positioning. It can also produce various new anti-theft nets (diamond anti-theft net, round tube square tube anti-theft net, door flower, etc.), and provide one-year warranty service for the whole machine.

Roller servo feeder, mountain type clamp feeder, hydraulic punching machine, servo feed square and rectangular pipe punching machine, CNC automatic punching machine for profiles is a new type of automatic processing equipment, which can process half holes or full holes on square pipes, round pipes and special-shaped pipes of different materials, Anhui Auto punching machine By changing the mold, it can also process various sizes and shapes of hole diameters, and can process guardrails, door flowers, shelves and other pipes, which are widely used in modern processing industry. Low cost. The cutting tool of the NC profile automatic punching machine consumes less energy, and the automatic operation saves a lot of manpower, and the pipe processing cost is greatly reduced. NC automatic punching machine for profiles is one of the advanced automatic punching equipment in the industry at present, Auto punching machine Which one is good It has many functions, high precision and low cost, which has brought great convenience to pipe processing, and is actually an important contributor to modern processing industry.

When the parts of the pipe punching machine are working, under the rated working conditions, they will not be damaged in any form, nor will they produce residual deformation beyond the allowable limit, and can ensure the normal operation and work of the machine, so it is considered that the parts meet the strength requirements. Anhui Auto punching machine In design, most important parts are checked by strength conditions (relevant strength theory in engineering mechanics), except some parts with small force or complex shape that cannot be calculated are determined by experience and experiments. major Auto punching machine If the strength of the parts is not enough, the overall fracture, surface contact fatigue or plastic deformation and other failures will occur and the working ability will be lost, so the strength requirements must be met when designing the parts.

During commissioning, it is not necessary to feed materials, but it is necessary to first raise the guide screw on the guide plate, and then gradually adjust the ram of the punch to the bottom dead center by inching. It is necessary to pay special attention to that the guide plate should not press the floating rod too low, otherwise the floating rod will be bent or broken. major Auto punching machine Which one is good When starting the punching machine for continuous punching, it is necessary to rotate the speed adjusting screw of the nc servo feeder clockwise. The slider moves slightly slowly, so that it can be seen whether the slider touches the nylon gasket and the length adjusting screw when it moves back and forth. Auto punching machine If the full-automatic punching machine only touches the length adjusting screw but not the nylon gasket when the sliding block moves back and forth, it is because the floating rod is lowered too deep, and the guide screw on the punching machine needs to be gradually raised.

The maintenance of the hydraulic rack punching machine can greatly delay the reduction of the accuracy of the hydraulic punching machine and extend its service life. The reduction of hydraulic punching machine precision is mainly manifested in the wear and plastic deformation of punching machine parts. Anhui Auto punching machine Which one is good Therefore, the lack of maintenance is one of the reasons why the accuracy of the NC punching machine is reduced. You can combine your own situation to see whether this is the reason for the reduction in accuracy. The movement relationship (time and movement) between components is damaged due to grinding and deformation of components, major Auto punching machine It will also reduce the accuracy of the hydraulic rack punching machine. Numerous practical experiences have proved that the accuracy of hydraulic punching machines without maintenance or improper maintenance can reduce much faster than that of well maintained hydraulic punching machines.