The space requirement is that the stainless steel punching machine can process multiple surfaces after the workpiece is installed at one time, so it is required that the fixture can meet the space requirement that each tool can approach all the machining surfaces. In addition, the supporting plate of the fixture moves, supports, sinks and rotates, so the fixture should not interfere with the machine tool in any way. Xi'an Full automatic punching machine Rapid re adjustment requires that the NC punching machine can change the processing object by quickly changing the processing program. In order to reduce the auxiliary time for changing tooling and the waiting idle time for valuable equipment, Full automatic punching machine manufactor When the workpiece is replaced, the fixture is required to have the function of rapid readjustment or replacement of positioning clamping elements. In addition, the processing time of a single piece increases due to the multi surface processing in NC processing. At this time, if the fixture is designed to be able to replace the workpiece outside the working area of the machine tool, the production efficiency can be improved

Energy saving and environmental protection, less noise, faster working efficiency than ordinary punches, small footprint, safe and secure operation. Xi'an Full automatic punching machine manufactor The punching needle is specially designed, and the time for changing the mold is short. Time delay protection circuit. When nobody operates the machine, the time delay protection switch will automatically enter the standby state. If you want to start work, you need to turn on the circuit switch again. The punching machine for handrail shelf of guardrail stairs is widely used in punching stainless steel, aluminum alloy bathroom, color steel, zinc steel guardrails, and is the equipment with fast pipe punching processing at present. Guardrail stair handrail punching machine can be customized to multiple working positions, easy and convenient to disassemble the mold, durable mold, easy for novices to use and so on. Full automatic punching machine It can debug and punch half hole or full hole at will, with flat punching and accurate positioning. It can also produce various new anti-theft nets (diamond anti-theft net, round tube square tube anti-theft net, door flower, etc.), and provide one-year warranty service for the whole machine.

First, observe the safety operation regulations of the numerical control punching machine. When the punching equipment is in place, the chassis should be leveled and stabilized. The punching frame should be vertical, and grounding protection should be done according to the construction power requirements. secondly, Xi'an Full automatic punching machine manufactor Before starting work, carefully check whether each component is properly configured and whether the fastening part is loose. If there is any abnormality, timely and correctly handle it. Numerically controlled punching machines are usually equipped with a variety of protective devices, Full automatic punching machine Before starting operation, make sure that these protective devices can work normally, which can improve the safety protection performance of the NC punching machine during operation and effectively reduce the accident rate during operation. In addition, the operator shall wear all kinds of armor as required, clean up the sundries on the machine table and within a certain range around, and irrelevant personnel shall not be close to the working area when the punching machine is running.

The insufficient strength of the punching machine for zinc steel guardrail is the direct cause of the fracture or excessive residual deformation of the parts in work. Xi'an Full automatic punching machine manufactor The strength of parts is divided into volume strength and surface contact strength. For example, if the stress produced by the pipe punching machine parts under the load is within a large volume, the strength of the parts under this stress state is called volume strength (strength for short). Full automatic punching machine If two parts change from point contact or line contact to small surface contact before and after being loaded, and their surfaces produce large local stress (called contact stress), then the strength of the parts is called surface contact strength (called contact strength for short).

When debugging the pointer friction force of the numerical control punching machine, first place the pointer at the zero point, and then place it at the test position, major Full automatic punching machine Then let the pendulum swing by releasing the button, which means that the pointer should not exceed the zero point. If it exceeds the zero point, it is necessary to inject lubricating oil into the pointer bearing or release the spring pressure of the pointer to debug it. The purpose of debugging the professional CNC punching machine is to ensure that the punching machine can have better punching quality and precision, so we carefully debug the punching machine that has just been purchased or replaced with more important parts, Full automatic punching machine manufactor In this way, the ideal punching effect can be obtained. At the same time, accurate debugging is also an effective protection for the service life of the NC punching machine itself.

In the past, the traditional punching machine usually used manual or semi-automatic punching to finish punching the workpiece. Now, with the continuous progress of punching machine technology, some shortcomings of the former manual punching machine itself are more and more obvious, Xi'an Full automatic punching machine manufactor The speed is very slow, so the efficiency is very low. If it is semi-automatic, automatic feeding cannot be carried out. CNC climbing frame punching machine needs frequent maintenance to ensure its life; Before operation, check whether the punch and die of the numerical control punching machine are matched, otherwise the punching machine host will be damaged. When assembling the upper and lower moulds, the models of the upper and lower moulds must be the same, and the fixing sleeve of the upper mould must be tightened. major Full automatic punching machine When placing the lower die, pay attention to the upward direction of the knife edge (the end with a small aperture), and do not damage the machine by installing it. Do not remove the quick coupler when the system has working pressure during operation. The screw rod and nut shall be lubricated with oil.