Once the NC climbing frame punching machine breaks down, its working efficiency will be seriously affected. If it is operated improperly, it will also have a more fatal impact on the life of the equipment. Taiyuan Zinc steel guardrail punching machine Price Using NC punching machine strictly according to standards can not only improve efficiency, but also extend service life. Determine whether your equipment is multi station or single station. Let's talk about the multi station CNC punching machine, Zinc steel guardrail punching machine When in use, only one oil circuit switch can be opened for operation at a time, and multiple oil circuit switches cannot be opened at the same time. Many people will use multiple switches simultaneously to improve efficiency, which will have a bad impact on equipment operation and processing quality.

During commissioning, it is not necessary to feed materials, but it is necessary to first raise the guide screw on the guide plate, and then gradually adjust the ram of the punch to the bottom dead center by inching. It is necessary to pay special attention to that the guide plate should not press the floating rod too low, otherwise the floating rod will be bent or broken. major Zinc steel guardrail punching machine Price When starting the punching machine for continuous punching, it is necessary to rotate the speed adjusting screw of the nc servo feeder clockwise. The slider moves slightly slowly, so that it can be seen whether the slider touches the nylon gasket and the length adjusting screw when it moves back and forth. Zinc steel guardrail punching machine If the full-automatic punching machine only touches the length adjusting screw but not the nylon gasket when the sliding block moves back and forth, it is because the floating rod is lowered too deep, and the guide screw on the punching machine needs to be gradually raised.

The ordinary pipe punching machine has no automatic positioning system, which is equivalent to a small punching machine that solves the feeding problem. Automatic pipe punching machine adds automatic positioning system on the basis of ordinary pipe punching machine, Taiyuan Zinc steel guardrail punching machine Price It greatly improves the precision and speed of punching, which can be understood as an automatic controlled high-precision small punch. The automatic pipe punching machine can not only position itself, but also automatically feed materials in batches, greatly saving manpower. The hydraulic automatic pipe punching machine produced by our factory adopts large torque AC synchronous servo motor, Zinc steel guardrail punching machine It is characterized by fast response, high positioning accuracy, low noise, small brake heat loss and long service life. Motion control: professional PLC controller, touch screen operation, simple and convenient.

The hydraulic high-speed punching machine is widely used for punching stainless steel (aluminum alloy) profiles, fan factories, air conditioning accessory factories, antenna factories and other hardware. Automatic and semi-automatic equipment can be customized. Taiyuan Zinc steel guardrail punching machine Anti theft net punching equipment, anti-theft window punching, protective window punching machine, anti-theft net equipment factory stainless steel anti-theft net hydraulic punching machine is your choice! The anti-theft net punching machine has a positioning rod with a scale, which is convenient for direct reading, accurate positioning, flat punching, etc, major Zinc steel guardrail punching machine It can adjust the perforation and single face at will. It is an ideal punching equipment for anti-theft net, guardrail and shelf

First, observe the safety operation regulations of the numerical control punching machine. When the punching equipment is in place, the chassis should be leveled and stabilized. The punching frame should be vertical, and grounding protection should be done according to the construction power requirements. secondly, Taiyuan Zinc steel guardrail punching machine Price Before starting work, carefully check whether each component is properly configured and whether the fastening part is loose. If there is any abnormality, timely and correctly handle it. Numerically controlled punching machines are usually equipped with a variety of protective devices, Zinc steel guardrail punching machine Before starting operation, make sure that these protective devices can work normally, which can improve the safety protection performance of the NC punching machine during operation and effectively reduce the accident rate during operation. In addition, the operator shall wear all kinds of armor as required, clean up the sundries on the machine table and within a certain range around, and irrelevant personnel shall not be close to the working area when the punching machine is running.

The reason why the NC automatic punching machine for profiles is favored by a large number of manufacturers is due to its excellent performance characteristics. multi-function. The NC profile automatic punching machine can form multiple holes of any shape on pipes of any specification and material at one time, the pipe wall can be of any thickness, and the hole center distance can be adjusted at will. high-precision. Taiyuan major Zinc steel guardrail punching machine The punching machine is controlled by the NC programming program of the machining center, and the processed hole shape is flat and the center distance is accurate. Easy to operate. Zinc steel guardrail punching machine The whole machine is controlled by microcomputer, which is easy to operate and learn. Super efficient. The equipment can meet the requirements of a large number of openings in a unit time, and its efficiency is much higher than that of traditional punches.