In order to give better play to the performance of the pipe punching machine, what matters should be paid attention to when the pipe punching machine is used and when it is maintained later? The oil of the pipe punching machine needs to be replaced regularly, basically every year, Shaanxi purchase Guardrail punching machine It should take less than three months, that is to say, it needs to be replaced within three months. Check whether there is any problem with the protective safety device, lubrication and other parts, and whether the relevant fastening screws are firm and loose. Guardrail punching machine Price When the mechanical operation is over, cut off the power supply and wipe the machine tool. In short, special attention should be paid to the daily use of the pipe punching machine, and regular inspection and maintenance should be carried out to ensure that the pipe punching machine can operate efficiently and normally.

When purchasing a NC punching machine, some details need attention. A small detail that is not paid attention to may affect the service life of the NC punching machine. Here is a detail that is easy to be ignored, that is, the polishing of the machine's steel plate, purchase Guardrail punching machine Price Some people may think that as long as the mold is finished, there will be no problem. It is not important whether the steel plate is ground or not, but in fact, this is not the case. If the steel plate under the mold is not ground smoothly, Guardrail punching machine It is likely to affect the service life of the mold, so it is likely to fail in the future use process.

During commissioning, it is not necessary to feed materials, but it is necessary to first raise the guide screw on the guide plate, and then gradually adjust the ram of the punch to the bottom dead center by inching. It is necessary to pay special attention to that the guide plate should not press the floating rod too low, otherwise the floating rod will be bent or broken. purchase Guardrail punching machine Price When starting the punching machine for continuous punching, it is necessary to rotate the speed adjusting screw of the nc servo feeder clockwise. The slider moves slightly slowly, so that it can be seen whether the slider touches the nylon gasket and the length adjusting screw when it moves back and forth. Guardrail punching machine If the full-automatic punching machine only touches the length adjusting screw but not the nylon gasket when the sliding block moves back and forth, it is because the floating rod is lowered too deep, and the guide screw on the punching machine needs to be gradually raised.

The reason why the NC automatic punching machine for profiles is favored by a large number of manufacturers is due to its excellent performance characteristics. multi-function. The NC profile automatic punching machine can form multiple holes of any shape on pipes of any specification and material at one time, the pipe wall can be of any thickness, and the hole center distance can be adjusted at will. high-precision. Shaanxi purchase Guardrail punching machine The punching machine is controlled by the NC programming program of the machining center, and the processed hole shape is flat and the center distance is accurate. Easy to operate. Guardrail punching machine The whole machine is controlled by microcomputer, which is easy to operate and learn. Super efficient. The equipment can meet the requirements of a large number of openings in a unit time, and its efficiency is much higher than that of traditional punches.

Energy saving and environmental protection, less noise, faster working efficiency than ordinary punches, small footprint, safe and secure operation. Shaanxi Guardrail punching machine Price The punching needle is specially designed, and the time for changing the mold is short. Time delay protection circuit. When nobody operates the machine, the time delay protection switch will automatically enter the standby state. If you want to start work, you need to turn on the circuit switch again. The punching machine for handrail shelf of guardrail stairs is widely used in punching stainless steel, aluminum alloy bathroom, color steel, zinc steel guardrails, and is the equipment with fast pipe punching processing at present. Guardrail stair handrail punching machine can be customized to multiple working positions, easy and convenient to disassemble the mold, durable mold, easy for novices to use and so on. Guardrail punching machine It can debug and punch half hole or full hole at will, with flat punching and accurate positioning. It can also produce various new anti-theft nets (diamond anti-theft net, round tube square tube anti-theft net, door flower, etc.), and provide one-year warranty service for the whole machine.