During commissioning, it is not necessary to feed materials, but it is necessary to first raise the guide screw on the guide plate, and then gradually adjust the ram of the punch to the bottom dead center by inching. It is necessary to pay special attention to that the guide plate should not press the floating rod too low, otherwise the floating rod will be bent or broken. major Semi automatic punching machine Price When starting the punching machine for continuous punching, it is necessary to rotate the speed adjusting screw of the nc servo feeder clockwise. The slider moves slightly slowly, so that it can be seen whether the slider touches the nylon gasket and the length adjusting screw when it moves back and forth. Semi automatic punching machine If the full-automatic punching machine only touches the length adjusting screw but not the nylon gasket when the sliding block moves back and forth, it is because the floating rod is lowered too deep, and the guide screw on the punching machine needs to be gradually raised.
When punching with the climbing frame punching machine, the die shall be installed and inserted into the pipe for punching. It is strictly prohibited to empty punch when there is no pipe, otherwise the die will be damaged, Huizhou Semi automatic punching machine When punching full holes, if there is no punching, it will automatically return. Please move the lower proximity switch downward to protect the mold. In addition, it should be noted that the CNC climbing frame punching machine needs inspection and maintenance after running for a period of time. Check whether the blade of the punching needle has been passivated. If it has been passivated, please remove the punching needle and grind it, or purchase a new punching needle from the climbing frame punching machine manufacturer. In winter, the temperature becomes low. To protect the equipment, Semi automatic punching machine Price If necessary, the engine should be started up and run idle for a period of time to warm up; If the equipment operates for a long time, check the temperature of the equipment. The temperature of the hydraulic oil should be controlled between 30 and 60 ℃.
The conveying precision of the feeder of the new construction climbing frame punch is relatively high, Huizhou Semi automatic punching machine When working, directly input the length of the feeder to achieve accurate realization and the required step distance. CNC punch feeder can be transformed into multi section feeding according to customer needs, saving energy. Semi automatic punching machine Price The CNC punch feeder has good safety performance, which can avoid accidents, reduce the labor intensity of workers, and create greater economic benefits.
Pipe automatic punching machine processing enterprises have been looking for a more suitable punching equipment with various functions. The high-quality Jinhai Mechanical CNC punching machine can automatically switch the working mode of double-sided hole and single-sided hole punching, Huizhou major Semi automatic punching machine At the same time, it can also realize punching processing of pipes, angle iron flat iron, channel steel groove aluminum and other profiles on the same machine, Semi automatic punching machine This has also saved a lot of equipment costs for enterprises and greatly increased the efficiency of production and processing to a certain extent.
In the past, the traditional punching machine usually used manual or semi-automatic punching to finish punching the workpiece. Now, with the continuous progress of punching machine technology, some shortcomings of the former manual punching machine itself are more and more obvious, Huizhou Semi automatic punching machine Price The speed is very slow, so the efficiency is very low. If it is semi-automatic, automatic feeding cannot be carried out. CNC climbing frame punching machine needs frequent maintenance to ensure its life; Before operation, check whether the punch and die of the numerical control punching machine are matched, otherwise the punching machine host will be damaged. When assembling the upper and lower moulds, the models of the upper and lower moulds must be the same, and the fixing sleeve of the upper mould must be tightened. major Semi automatic punching machine When placing the lower die, pay attention to the upward direction of the knife edge (the end with a small aperture), and do not damage the machine by installing it. Do not remove the quick coupler when the system has working pressure during operation. The screw rod and nut shall be lubricated with oil.
During the test run of the full-automatic punching machine, the sliding block moves back and forth. If the stainless steel pipe fence punching machine only touches the nylon gasket and does not touch the length adjustment screw, it is because the floating rod can not be lowered deep, and the guide screw on the punching machine needs to be gradually adjusted downward. major Semi automatic punching machine Price The hydraulic high-speed punching machine is widely used in stainless steel (zinc steel, aluminum alloy, steel pipe, welded pipe, seamless pipe, square pipe, round pipe, flat iron, channel steel, angle iron) profiles, fan factories, air conditioning parts factories, antenna factories, shelf factories, metal furniture factories, automobile parts factories Huizhou Semi automatic punching machine Building materials manufacturers and other hardware pipe fittings, profiles punching processing. Automatic and semi-automatic equipment can be customized according to customer requirements.
