This model is equipped with two punching cylinders, which can be used for punching single or multiple cylinders respectively. The upper cylinder can be adjusted to punch half or full holes. The climbing frame automatic punching machine is easy to operate, superior in quality and reasonable in price, Beijing Semi automatic hydraulic punching machine It meets the quality requirements of domestic and foreign markets, and can process high-quality and high-precision workpieces. The punching hole of this machine is flat without burrs, and the positioning is accurate. The clamping, lifting and other mechanisms of the whole machine are controlled by air pressure or hydraulic pressure. The positioning of workpieces (X, Y coordinates) is driven by servo, and the control of the whole machine is controlled by microcomputer, Semi automatic hydraulic punching machine Which one is good Parameter setting and operation switching are performed through the touch screen interface, which is simple and convenient to operate, and can store more than 100 product processing parameters.

In order to ensure that the round pipe punching machine has good quality and use effect, it is recommended that enterprises choose genuine hydraulic oil with relatively high cost performance. Because the hydraulic oil with good brand has high purity and less impurities, it will not be worn by impurities after being used for the round pipe punching machine, and the oil is not easy to deteriorate, Beijing Semi automatic hydraulic punching machine Can play a better role. As the hydraulic system is an important part of the pipe punching machine, and the hydraulic oil plays a crucial role in it, major Semi automatic hydraulic punching machine When using the round pipe punching machine, enterprises should not only use the equipment according to the operating rules, but also pay attention to adding and replacing the hydraulic oil in the hydraulic system regularly to ensure that the quality and life of the round pipe punching machine will not be affected.

Energy saving and environmental protection, less noise, faster working efficiency than ordinary punches, small footprint, safe and secure operation. Beijing Semi automatic hydraulic punching machine Which one is good The punching needle is specially designed, and the time for changing the mold is short. Time delay protection circuit. When nobody operates the machine, the time delay protection switch will automatically enter the standby state. If you want to start work, you need to turn on the circuit switch again. The punching machine for handrail shelf of guardrail stairs is widely used in punching stainless steel, aluminum alloy bathroom, color steel, zinc steel guardrails, and is the equipment with fast pipe punching processing at present. Guardrail stair handrail punching machine can be customized to multiple working positions, easy and convenient to disassemble the mold, durable mold, easy for novices to use and so on. Semi automatic hydraulic punching machine It can debug and punch half hole or full hole at will, with flat punching and accurate positioning. It can also produce various new anti-theft nets (diamond anti-theft net, round tube square tube anti-theft net, door flower, etc.), and provide one-year warranty service for the whole machine.

In order to give better play to the performance of the pipe punching machine, what matters should be paid attention to when the pipe punching machine is used and when it is maintained later? The oil of the pipe punching machine needs to be replaced regularly, basically every year, Beijing major Semi automatic hydraulic punching machine It should take less than three months, that is to say, it needs to be replaced within three months. Check whether there is any problem with the protective safety device, lubrication and other parts, and whether the relevant fastening screws are firm and loose. Semi automatic hydraulic punching machine Which one is good When the mechanical operation is over, cut off the power supply and wipe the machine tool. In short, special attention should be paid to the daily use of the pipe punching machine, and regular inspection and maintenance should be carried out to ensure that the pipe punching machine can operate efficiently and normally.

Most of the current shelves, fences, guardrails and anti-theft nets are processed by CNC punching machines, Beijing Semi automatic hydraulic punching machine It is very fast in speed and high in accuracy. There is no burr. The hole surface has a good finish. Now using the CNC punching machine will make it easier to clamp the workpiece, major Semi automatic hydraulic punching machine It is also unnecessary to use some special fixtures during processing, which can effectively reduce the cost of fixtures, avoid multiple clamping, and effectively improve the product process.

Drilling is the process of drilling holes on the processing materials with a drill bit, while the pipe punching machine is the process of punching holes under the drill bit by gravity. Automatic pipe punching machine is suitable for processing soft materials, Beijing Semi automatic hydraulic punching machine Because the holes drilled by the drilling machine will have burrs and unevenness. The drilling machine is suitable for processing hard materials, because the punching force of the pipe punching machine often causes cracks in the processing materials. Semi automatic hydraulic punching machine Which one is good The processing objects of punching machine and pipe punching machine are similar to a large extent. The punching machine is divided into ordinary punching machine, rapid punching machine, etc. Since the punching machine needs a feeding system, its volume is generally large. The automatic pipe punching machine is a further development of the punch, which solves the problem that the punch needs an independent feeding system, so it is small in size.