During commissioning, it is not necessary to feed materials, but it is necessary to first raise the guide screw on the guide plate, and then gradually adjust the ram of the punch to the bottom dead center by inching. It is necessary to pay special attention to that the guide plate should not press the floating rod too low, otherwise the floating rod will be bent or broken. purchase Auto punching machine Which one is good When starting the punching machine for continuous punching, it is necessary to rotate the speed adjusting screw of the nc servo feeder clockwise. The slider moves slightly slowly, so that it can be seen whether the slider touches the nylon gasket and the length adjusting screw when it moves back and forth. Auto punching machine If the full-automatic punching machine only touches the length adjusting screw but not the nylon gasket when the sliding block moves back and forth, it is because the floating rod is lowered too deep, and the guide screw on the punching machine needs to be gradually raised.

In the past, the traditional punching machine usually used manual or semi-automatic punching to finish punching the workpiece. Now, with the continuous progress of punching machine technology, some shortcomings of the former manual punching machine itself are more and more obvious, Hebei Auto punching machine Which one is good The speed is very slow, so the efficiency is very low. If it is semi-automatic, automatic feeding cannot be carried out. CNC climbing frame punching machine needs frequent maintenance to ensure its life; Before operation, check whether the punch and die of the numerical control punching machine are matched, otherwise the punching machine host will be damaged. When assembling the upper and lower moulds, the models of the upper and lower moulds must be the same, and the fixing sleeve of the upper mould must be tightened. purchase Auto punching machine When placing the lower die, pay attention to the upward direction of the knife edge (the end with a small aperture), and do not damage the machine by installing it. Do not remove the quick coupler when the system has working pressure during operation. The screw rod and nut shall be lubricated with oil.

High efficiency and high precision of products are the main direction. Speed and precision are two important indicators of CNC machine tools such as punching machines, which directly affect the quality and grade of products, the production cycle of products and the competitiveness in the market. Hebei Auto punching machine Which one is good The improvement of machining accuracy requires improving the control accuracy of the system; High efficiency requires improving the parameters of high-end CNC system. secondly, Auto punching machine We should develop in the direction of intelligence. Intelligent punching machines are required to have the characteristics of automation and intelligence. Artificial intelligence is constantly infiltrating and developing in the computer field. Numerical control systems are developing in the direction of intelligence. With the help of intelligent technology, equipment has the functions of adaptive control, intelligent diagnosis, intelligent monitoring, etc.

The insufficient strength of the punching machine for zinc steel guardrail is the direct cause of the fracture or excessive residual deformation of the parts in work. Hebei Auto punching machine Which one is good The strength of parts is divided into volume strength and surface contact strength. For example, if the stress produced by the pipe punching machine parts under the load is within a large volume, the strength of the parts under this stress state is called volume strength (strength for short). Auto punching machine If two parts change from point contact or line contact to small surface contact before and after being loaded, and their surfaces produce large local stress (called contact stress), then the strength of the parts is called surface contact strength (called contact strength for short).

In order to give better play to the performance of the pipe punching machine, what matters should be paid attention to when the pipe punching machine is used and when it is maintained later? The oil of the pipe punching machine needs to be replaced regularly, basically every year, Hebei purchase Auto punching machine It should take less than three months, that is to say, it needs to be replaced within three months. Check whether there is any problem with the protective safety device, lubrication and other parts, and whether the relevant fastening screws are firm and loose. Auto punching machine Which one is good When the mechanical operation is over, cut off the power supply and wipe the machine tool. In short, special attention should be paid to the daily use of the pipe punching machine, and regular inspection and maintenance should be carried out to ensure that the pipe punching machine can operate efficiently and normally.

The climbing frame punching machine is mainly used for punching operations in industrial processing and manufacturing. Because different processing materials need to be punched in the industrial processing and manufacturing fields and in the building materials industry, Hebei Auto punching machine Which one is good Choosing a high-quality square tube punching machine can effectively improve the overall processing efficiency in the processing field. People should pay attention to the regular maintenance and cleaning of the square tube punching machine when using it. Since there are more or less oil stains and sundries left on the surface of the machine after each use, Auto punching machine In order to better maintain the normal operation of the equipment, it is not only necessary to clean the equipment every day for oil stains and sundries, but also to regularly overhaul the key parts of the equipment with abnormal looseness at intervals.