Roller servo feeder, mountain type clamp feeder, hydraulic punching machine, servo feed square and rectangular pipe punching machine, CNC automatic punching machine for profiles is a new type of automatic processing equipment, which can process half holes or full holes on square pipes, round pipes and special-shaped pipes of different materials, Jilin Stainless steel punching machine By changing the mold, it can also process various sizes and shapes of hole diameters, and can process guardrails, door flowers, shelves and other pipes, which are widely used in modern processing industry. Low cost. The cutting tool of the NC profile automatic punching machine consumes less energy, and the automatic operation saves a lot of manpower, and the pipe processing cost is greatly reduced. NC automatic punching machine for profiles is one of the advanced automatic punching equipment in the industry at present, Stainless steel punching machine Which one is good It has many functions, high precision and low cost, which has brought great convenience to pipe processing, and is actually an important contributor to modern processing industry.

First, observe the safety operation regulations of the numerical control punching machine. When the punching equipment is in place, the chassis should be leveled and stabilized. The punching frame should be vertical, and grounding protection should be done according to the construction power requirements. secondly, Jilin Stainless steel punching machine Which one is good Before starting work, carefully check whether each component is properly configured and whether the fastening part is loose. If there is any abnormality, timely and correctly handle it. Numerically controlled punching machines are usually equipped with a variety of protective devices, Stainless steel punching machine Before starting operation, make sure that these protective devices can work normally, which can improve the safety protection performance of the NC punching machine during operation and effectively reduce the accident rate during operation. In addition, the operator shall wear all kinds of armor as required, clean up the sundries on the machine table and within a certain range around, and irrelevant personnel shall not be close to the working area when the punching machine is running.

With the continuous development of China's manufacturing industry, the technical level of punching machines and other equipment is required to be higher and higher. The requirements of the market for equipment determine that punching machine manufacturers should constantly improve the technical level of their products. Rack punching machine manufacturers should follow the market development and produce high-end punching equipment, Jilin major Stainless steel punching machine With the help of the intelligent trend of the development of China's machine tool industry, the punching machine technology is brought to a higher level. In addition, Stainless steel punching machine When punching, after the mold is installed, insert the pipe for punching. It is strictly prohibited to empty punch when there is no pipe, otherwise the mold will be damaged. When punching the full hole, if there is no punching, it will automatically return. Please move the lower proximity switch downward to protect the mold.

The stamping part adopts hydraulic oil cylinder, which uses oil as the working medium to transmit movement through the change of sealing volume, Jilin major Stainless steel punching machine Power is transmitted through the pressure inside the oil. Digital control punch to achieve the feeding function, climbing frame automatic punching machine manufacturers, computers installed with specific programs to control the system automatic machine tools. The control system can process compiled codes with conditioning and logic, and then realize the machining of parts. Stainless steel punching machine The CNC punch feeder adopts two groups of simultaneous feeding and conveying, which avoids the disadvantage of material slippage in the process of conveying materials at high speed and long distance, and avoids stretching of the conveyed materials, as well as the effect of automatic correction of materials.

Once the high-end CNC punching machine breaks down, its working efficiency will be seriously affected. If it is improperly operated, it will also have a more fatal impact on the life of the equipment. major Stainless steel punching machine Which one is good Using the rack punching machine in strict accordance with the standard can not only improve the efficiency, but also extend the service life. Determine whether your equipment is multi station or single station, and talk about the multi station punching machine, Jilin Stainless steel punching machine When in use, only one oil circuit switch can be opened for operation at a time, and multiple oil circuit switches cannot be opened at the same time. Many people will use multiple switches simultaneously to improve efficiency, which will have a bad impact on equipment operation and processing quality.

The hydraulic high-speed punching machine is widely used for punching stainless steel (aluminum alloy) profiles, fan factories, air conditioning accessory factories, antenna factories and other hardware. Automatic and semi-automatic equipment can be customized. Jilin Stainless steel punching machine Anti theft net punching equipment, anti-theft window punching, protective window punching machine, anti-theft net equipment factory stainless steel anti-theft net hydraulic punching machine is your choice! The anti-theft net punching machine has a positioning rod with a scale, which is convenient for direct reading, accurate positioning, flat punching, etc, major Stainless steel punching machine It can adjust the perforation and single face at will. It is an ideal punching equipment for anti-theft net, guardrail and shelf