Don't just look at the price, but consider the manufacturing process of CNC punching machines from the perspective of quality and cycle, which can be roughly divided into ten categories. The climbing frame punching machine is based on different requirements of part materials, physical and chemical properties, mechanical strength, dimensional accuracy, surface finish, service life, economy, etc, Jinan Stainless steel CNC punching machine Select different types of dies to form. Some parts have special requirements when forming, and the CNC punching machine also needs to use advanced processes such as hot runner, gas assisted molding, cylinder, etc. major Stainless steel CNC punching machine In general, whether the machine tool has a blank holder mechanism, or even a side lubricant, multi station progressive, etc., should be considered for large stamping dies. The climbing frame punching machine should not only focus on product design, but also ignore the service life of the mold.

First, observe the safety operation regulations of the numerical control punching machine. When the punching equipment is in place, the chassis should be leveled and stabilized. The punching frame should be vertical, and grounding protection should be done according to the construction power requirements. secondly, Jinan Stainless steel CNC punching machine Price Before starting work, carefully check whether each component is properly configured and whether the fastening part is loose. If there is any abnormality, timely and correctly handle it. Numerically controlled punching machines are usually equipped with a variety of protective devices, Stainless steel CNC punching machine Before starting operation, make sure that these protective devices can work normally, which can improve the safety protection performance of the NC punching machine during operation and effectively reduce the accident rate during operation. In addition, the operator shall wear all kinds of armor as required, clean up the sundries on the machine table and within a certain range around, and irrelevant personnel shall not be close to the working area when the punching machine is running.

In order to give better play to the performance of the pipe punching machine, what matters should be paid attention to when the pipe punching machine is used and when it is maintained later? The oil of the pipe punching machine needs to be replaced regularly, basically every year, Jinan major Stainless steel CNC punching machine It should take less than three months, that is to say, it needs to be replaced within three months. Check whether there is any problem with the protective safety device, lubrication and other parts, and whether the relevant fastening screws are firm and loose. Stainless steel CNC punching machine Price When the mechanical operation is over, cut off the power supply and wipe the machine tool. In short, special attention should be paid to the daily use of the pipe punching machine, and regular inspection and maintenance should be carried out to ensure that the pipe punching machine can operate efficiently and normally.

During commissioning, it is not necessary to feed materials, but it is necessary to first raise the guide screw on the guide plate, and then gradually adjust the ram of the punch to the bottom dead center by inching. It is necessary to pay special attention to that the guide plate should not press the floating rod too low, otherwise the floating rod will be bent or broken. major Stainless steel CNC punching machine Price When starting the punching machine for continuous punching, it is necessary to rotate the speed adjusting screw of the nc servo feeder clockwise. The slider moves slightly slowly, so that it can be seen whether the slider touches the nylon gasket and the length adjusting screw when it moves back and forth. Stainless steel CNC punching machine If the full-automatic punching machine only touches the length adjusting screw but not the nylon gasket when the sliding block moves back and forth, it is because the floating rod is lowered too deep, and the guide screw on the punching machine needs to be gradually raised.

The space requirement is that the stainless steel punching machine can process multiple surfaces after the workpiece is installed at one time, so it is required that the fixture can meet the space requirement that each tool can approach all the machining surfaces. In addition, the supporting plate of the fixture moves, supports, sinks and rotates, so the fixture should not interfere with the machine tool in any way. Jinan Stainless steel CNC punching machine Rapid re adjustment requires that the NC punching machine can change the processing object by quickly changing the processing program. In order to reduce the auxiliary time for changing tooling and the waiting idle time for valuable equipment, Stainless steel CNC punching machine Price When the workpiece is replaced, the fixture is required to have the function of rapid readjustment or replacement of positioning clamping elements. In addition, the processing time of a single piece increases due to the multi surface processing in NC processing. At this time, if the fixture is designed to be able to replace the workpiece outside the working area of the machine tool, the production efficiency can be improved