In order to give better play to the performance of the pipe punching machine, what matters should be paid attention to when the pipe punching machine is used and when it is maintained later? The oil of the pipe punching machine needs to be replaced regularly, basically every year, Shandong purchase Climbing frame CNC punching machine It should take less than three months, that is to say, it needs to be replaced within three months. Check whether there is any problem with the protective safety device, lubrication and other parts, and whether the relevant fastening screws are firm and loose. Climbing frame CNC punching machine manufactor When the mechanical operation is over, cut off the power supply and wipe the machine tool. In short, special attention should be paid to the daily use of the pipe punching machine, and regular inspection and maintenance should be carried out to ensure that the pipe punching machine can operate efficiently and normally.
During commissioning, it is not necessary to feed materials, but it is necessary to first raise the guide screw on the guide plate, and then gradually adjust the ram of the punch to the bottom dead center by inching. It is necessary to pay special attention to that the guide plate should not press the floating rod too low, otherwise the floating rod will be bent or broken. purchase Climbing frame CNC punching machine manufactor When starting the punching machine for continuous punching, it is necessary to rotate the speed adjusting screw of the nc servo feeder clockwise. The slider moves slightly slowly, so that it can be seen whether the slider touches the nylon gasket and the length adjusting screw when it moves back and forth. Climbing frame CNC punching machine If the full-automatic punching machine only touches the length adjusting screw but not the nylon gasket when the sliding block moves back and forth, it is because the floating rod is lowered too deep, and the guide screw on the punching machine needs to be gradually raised.
This model is equipped with two punching cylinders, which can be used for punching single or multiple cylinders respectively. The upper cylinder can be adjusted to punch half or full holes. The climbing frame automatic punching machine is easy to operate, superior in quality and reasonable in price, Shandong Climbing frame CNC punching machine It meets the quality requirements of domestic and foreign markets, and can process high-quality and high-precision workpieces. The punching hole of this machine is flat without burrs, and the positioning is accurate. The clamping, lifting and other mechanisms of the whole machine are controlled by air pressure or hydraulic pressure. The positioning of workpieces (X, Y coordinates) is driven by servo, and the control of the whole machine is controlled by microcomputer, Climbing frame CNC punching machine manufactor Parameter setting and operation switching are performed through the touch screen interface, which is simple and convenient to operate, and can store more than 100 product processing parameters.
When purchasing a NC punching machine, some details need attention. A small detail that is not paid attention to may affect the service life of the NC punching machine. Here is a detail that is easy to be ignored, that is, the polishing of the machine's steel plate, purchase Climbing frame CNC punching machine manufactor Some people may think that as long as the mold is finished, there will be no problem. It is not important whether the steel plate is ground or not, but in fact, this is not the case. If the steel plate under the mold is not ground smoothly, Climbing frame CNC punching machine It is likely to affect the service life of the mold, so it is likely to fail in the future use process.
Once the NC climbing frame punching machine breaks down, its working efficiency will be seriously affected. If it is operated improperly, it will also have a more fatal impact on the life of the equipment. Shandong Climbing frame CNC punching machine manufactor Using NC punching machine strictly according to standards can not only improve efficiency, but also extend service life. Determine whether your equipment is multi station or single station. Let's talk about the multi station CNC punching machine, Climbing frame CNC punching machine When in use, only one oil circuit switch can be opened for operation at a time, and multiple oil circuit switches cannot be opened at the same time. Many people will use multiple switches simultaneously to improve efficiency, which will have a bad impact on equipment operation and processing quality.
At present, the first-class full-automatic punching machine for zinc steel guardrail has been widely used in our life. Shandong purchase Climbing frame CNC punching machine Customers who often use full-automatic punching machines for zinc steel guardrails should all know that because of its simple structure, easy operation, light weight, convenient handling and other advantages, the full-automatic punching machine has been used in many aspects such as stainless steel, anti-theft net, aluminum alloy and so on. Pay attention to the grinding of the machine table steel plate. This is the key point. Customers should know that, Climbing frame CNC punching machine The machine will produce varying degrees of "vibration" during operation, but people pay less attention to the looseness and wear of the mold and the underlying steel plate during the vibration process, but the problem comes out after a long time, so the customer must pay attention to the polishing of the table steel plate of the full-automatic punching machine.
