In the past, the traditional punching machine usually used manual or semi-automatic punching to finish punching the workpiece. Now, with the continuous progress of punching machine technology, some shortcomings of the former manual punching machine itself are more and more obvious, Hunan Full automatic punching machine Price The speed is very slow, so the efficiency is very low. If it is semi-automatic, automatic feeding cannot be carried out. CNC climbing frame punching machine needs frequent maintenance to ensure its life; Before operation, check whether the punch and die of the numerical control punching machine are matched, otherwise the punching machine host will be damaged. When assembling the upper and lower moulds, the models of the upper and lower moulds must be the same, and the fixing sleeve of the upper mould must be tightened. major Full automatic punching machine When placing the lower die, pay attention to the upward direction of the knife edge (the end with a small aperture), and do not damage the machine by installing it. Do not remove the quick coupler when the system has working pressure during operation. The screw rod and nut shall be lubricated with oil.

First, observe the safety operation regulations of the numerical control punching machine. When the punching equipment is in place, the chassis should be leveled and stabilized. The punching frame should be vertical, and grounding protection should be done according to the construction power requirements. secondly, Hunan Full automatic punching machine Price Before starting work, carefully check whether each component is properly configured and whether the fastening part is loose. If there is any abnormality, timely and correctly handle it. Numerically controlled punching machines are usually equipped with a variety of protective devices, Full automatic punching machine Before starting operation, make sure that these protective devices can work normally, which can improve the safety protection performance of the NC punching machine during operation and effectively reduce the accident rate during operation. In addition, the operator shall wear all kinds of armor as required, clean up the sundries on the machine table and within a certain range around, and irrelevant personnel shall not be close to the working area when the punching machine is running.

Once the high-end CNC punching machine breaks down, its working efficiency will be seriously affected. If it is improperly operated, it will also have a more fatal impact on the life of the equipment. major Full automatic punching machine Price Using the rack punching machine in strict accordance with the standard can not only improve the efficiency, but also extend the service life. Determine whether your equipment is multi station or single station, and talk about the multi station punching machine, Hunan Full automatic punching machine When in use, only one oil circuit switch can be opened for operation at a time, and multiple oil circuit switches cannot be opened at the same time. Many people will use multiple switches simultaneously to improve efficiency, which will have a bad impact on equipment operation and processing quality.

Energy saving and environmental protection, less noise, faster working efficiency than ordinary punches, small footprint, safe and secure operation. Hunan Full automatic punching machine Price The punching needle is specially designed, and the time for changing the mold is short. Time delay protection circuit. When nobody operates the machine, the time delay protection switch will automatically enter the standby state. If you want to start work, you need to turn on the circuit switch again. The punching machine for handrail shelf of guardrail stairs is widely used in punching stainless steel, aluminum alloy bathroom, color steel, zinc steel guardrails, and is the equipment with fast pipe punching processing at present. Guardrail stair handrail punching machine can be customized to multiple working positions, easy and convenient to disassemble the mold, durable mold, easy for novices to use and so on. Full automatic punching machine It can debug and punch half hole or full hole at will, with flat punching and accurate positioning. It can also produce various new anti-theft nets (diamond anti-theft net, round tube square tube anti-theft net, door flower, etc.), and provide one-year warranty service for the whole machine.

In order to ensure that the round pipe punching machine has good quality and use effect, it is recommended that enterprises choose genuine hydraulic oil with relatively high cost performance. Because the hydraulic oil with good brand has high purity and less impurities, it will not be worn by impurities after being used for the round pipe punching machine, and the oil is not easy to deteriorate, Hunan Full automatic punching machine Can play a better role. As the hydraulic system is an important part of the pipe punching machine, and the hydraulic oil plays a crucial role in it, major Full automatic punching machine When using the round pipe punching machine, enterprises should not only use the equipment according to the operating rules, but also pay attention to adding and replacing the hydraulic oil in the hydraulic system regularly to ensure that the quality and life of the round pipe punching machine will not be affected.

In order to ensure the flexibility of the pipe punching machine, Hunan Full automatic punching machine Price The sliding block also needs to be often injected with lubricating oil. Generally, before the pipe punching machine runs, it needs to be injected with oil. The column surface of the pipe punching machine also needs to be clean. If the pipe punching machine has not been used for a long time Hunan Full automatic punching machine The surface shall be cleaned and coated with antirust oil to avoid corrosion and rust. The pipe punching machine should also be checked regularly, and the pressure gauge should be checked once every 6 months.