In order to enable the square pipe punching machine to effectively achieve a sound punching effect, the punching of the equipment should be checked regularly, purchase Stainless steel CNC punching machine And ensure that there is no aging in the mold to prevent the punching effect of processed objects from being affected. In order to make the square pipe punching machine have a better punching effect and extend its service life, Stainless steel CNC punching machine Which one is good During the use, adequate maintenance and overhaul shall be carried out, and the greasy dirt and other dirt on the equipment shall be cleaned timely after each punching operation.

Energy saving and environmental protection, less noise, faster working efficiency than ordinary punches, small footprint, safe and secure operation. Zhongshan Stainless steel CNC punching machine Which one is good The punching needle is specially designed, and the time for changing the mold is short. Time delay protection circuit. When nobody operates the machine, the time delay protection switch will automatically enter the standby state. If you want to start work, you need to turn on the circuit switch again. The punching machine for handrail shelf of guardrail stairs is widely used in punching stainless steel, aluminum alloy bathroom, color steel, zinc steel guardrails, and is the equipment with fast pipe punching processing at present. Guardrail stair handrail punching machine can be customized to multiple working positions, easy and convenient to disassemble the mold, durable mold, easy for novices to use and so on. Stainless steel CNC punching machine It can debug and punch half hole or full hole at will, with flat punching and accurate positioning. It can also produce various new anti-theft nets (diamond anti-theft net, round tube square tube anti-theft net, door flower, etc.), and provide one-year warranty service for the whole machine.

The ordinary pipe punching machine has no automatic positioning system, which is equivalent to a small punching machine that solves the feeding problem. Automatic pipe punching machine adds automatic positioning system on the basis of ordinary pipe punching machine, Zhongshan Stainless steel CNC punching machine Which one is good It greatly improves the precision and speed of punching, which can be understood as an automatic controlled high-precision small punch. The automatic pipe punching machine can not only position itself, but also automatically feed materials in batches, greatly saving manpower. The hydraulic automatic pipe punching machine produced by our factory adopts large torque AC synchronous servo motor, Stainless steel CNC punching machine It is characterized by fast response, high positioning accuracy, low noise, small brake heat loss and long service life. Motion control: professional PLC controller, touch screen operation, simple and convenient.

First, observe the safety operation regulations of the numerical control punching machine. When the punching equipment is in place, the chassis should be leveled and stabilized. The punching frame should be vertical, and grounding protection should be done according to the construction power requirements. secondly, Zhongshan Stainless steel CNC punching machine Which one is good Before starting work, carefully check whether each component is properly configured and whether the fastening part is loose. If there is any abnormality, timely and correctly handle it. Numerically controlled punching machines are usually equipped with a variety of protective devices, Stainless steel CNC punching machine Before starting operation, make sure that these protective devices can work normally, which can improve the safety protection performance of the NC punching machine during operation and effectively reduce the accident rate during operation. In addition, the operator shall wear all kinds of armor as required, clean up the sundries on the machine table and within a certain range around, and irrelevant personnel shall not be close to the working area when the punching machine is running.

This model is equipped with two punching cylinders, which can be used for punching single or multiple cylinders respectively. The upper cylinder can be adjusted to punch half or full holes. The climbing frame automatic punching machine is easy to operate, superior in quality and reasonable in price, Zhongshan Stainless steel CNC punching machine It meets the quality requirements of domestic and foreign markets, and can process high-quality and high-precision workpieces. The punching hole of this machine is flat without burrs, and the positioning is accurate. The clamping, lifting and other mechanisms of the whole machine are controlled by air pressure or hydraulic pressure. The positioning of workpieces (X, Y coordinates) is driven by servo, and the control of the whole machine is controlled by microcomputer, Stainless steel CNC punching machine Which one is good Parameter setting and operation switching are performed through the touch screen interface, which is simple and convenient to operate, and can store more than 100 product processing parameters.