During commissioning, it is not necessary to feed materials, but it is necessary to first raise the guide screw on the guide plate, and then gradually adjust the ram of the punch to the bottom dead center by inching. It is necessary to pay special attention to that the guide plate should not press the floating rod too low, otherwise the floating rod will be bent or broken. purchase Stainless steel punching machine Which one is good When starting the punching machine for continuous punching, it is necessary to rotate the speed adjusting screw of the nc servo feeder clockwise. The slider moves slightly slowly, so that it can be seen whether the slider touches the nylon gasket and the length adjusting screw when it moves back and forth. Stainless steel punching machine If the full-automatic punching machine only touches the length adjusting screw but not the nylon gasket when the sliding block moves back and forth, it is because the floating rod is lowered too deep, and the guide screw on the punching machine needs to be gradually raised.

Science and technology bring convenience to people, improve work efficiency and increase income. The CNC climbing frame punching machine is a fast punching equipment independently developed by Jinhai, which can be used for punching C-shaped steel, square steel and channel steel. Chongqing Stainless steel punching machine Which one is good It is widely used in mining, tunnel, construction engineering and other fields. Compared with the same type of products on the market, Stainless steel punching machine This product improves the punching precision and speed, and is suitable for two feed servo motors, imported hydraulic oil pump, contact phone of climbing frame automatic punching machine, PLC operating system, and can also match a variety of molds, achieving a true sense of "multi-function". The CNC climbing frame full-automatic punching machine works better together with the special die produced by Yinjiang, bringing infinite convenience to new and old users.

The hydraulic high-speed punching machine is widely used for punching stainless steel (aluminum alloy) profiles, fan factories, air conditioning accessory factories, antenna factories and other hardware. Automatic and semi-automatic equipment can be customized. Chongqing Stainless steel punching machine Anti theft net punching equipment, anti-theft window punching, protective window punching machine, anti-theft net equipment factory stainless steel anti-theft net hydraulic punching machine is your choice! The anti-theft net punching machine has a positioning rod with a scale, which is convenient for direct reading, accurate positioning, flat punching, etc, purchase Stainless steel punching machine It can adjust the perforation and single face at will. It is an ideal punching equipment for anti-theft net, guardrail and shelf

In order to give better play to the performance of the pipe punching machine, what matters should be paid attention to when the pipe punching machine is used and when it is maintained later? The oil of the pipe punching machine needs to be replaced regularly, basically every year, Chongqing purchase Stainless steel punching machine It should take less than three months, that is to say, it needs to be replaced within three months. Check whether there is any problem with the protective safety device, lubrication and other parts, and whether the relevant fastening screws are firm and loose. Stainless steel punching machine Which one is good When the mechanical operation is over, cut off the power supply and wipe the machine tool. In short, special attention should be paid to the daily use of the pipe punching machine, and regular inspection and maintenance should be carried out to ensure that the pipe punching machine can operate efficiently and normally.

Drilling is the process of drilling holes on the processing materials with a drill bit, while the pipe punching machine is the process of punching holes under the drill bit by gravity. Automatic pipe punching machine is suitable for processing soft materials, Chongqing Stainless steel punching machine Because the holes drilled by the drilling machine will have burrs and unevenness. The drilling machine is suitable for processing hard materials, because the punching force of the pipe punching machine often causes cracks in the processing materials. Stainless steel punching machine Which one is good The processing objects of punching machine and pipe punching machine are similar to a large extent. The punching machine is divided into ordinary punching machine, rapid punching machine, etc. Since the punching machine needs a feeding system, its volume is generally large. The automatic pipe punching machine is a further development of the punch, which solves the problem that the punch needs an independent feeding system, so it is small in size.

We often consider what numerical control mechanical equipment is the ideal of the mechanical industry. purchase Stainless steel punching machine High degree of automation control; The NC punching machine with high degree of automation has become a good helper for pipe processing enterprises. Employees only need to master some key data, Chongqing Stainless steel punching machine Which one is good And these devices are usually simple to operate, fast and efficient. CNC punching machine has high cost performance ratio; At present, there are few enterprises that can really reach this standard, because some enterprises in the NC punching machine industry only care about the price, and do not care about product quality and after-sales.