Roller servo feeder, mountain type clamp feeder, hydraulic punching machine, servo feed square and rectangular pipe punching machine, CNC automatic punching machine for profiles is a new type of automatic processing equipment, which can process half holes or full holes on square pipes, round pipes and special-shaped pipes of different materials, Guangdong Rack punching machine By changing the mold, it can also process various sizes and shapes of hole diameters, and can process guardrails, door flowers, shelves and other pipes, which are widely used in modern processing industry. Low cost. The cutting tool of the NC profile automatic punching machine consumes less energy, and the automatic operation saves a lot of manpower, and the pipe processing cost is greatly reduced. NC automatic punching machine for profiles is one of the advanced automatic punching equipment in the industry at present, Rack punching machine Price It has many functions, high precision and low cost, which has brought great convenience to pipe processing, and is actually an important contributor to modern processing industry.

In the past, the traditional punching machine usually used manual or semi-automatic punching to finish punching the workpiece. Now, with the continuous progress of punching machine technology, some shortcomings of the former manual punching machine itself are more and more obvious, Guangdong Rack punching machine Price The speed is very slow, so the efficiency is very low. If it is semi-automatic, automatic feeding cannot be carried out. CNC climbing frame punching machine needs frequent maintenance to ensure its life; Before operation, check whether the punch and die of the numerical control punching machine are matched, otherwise the punching machine host will be damaged. When assembling the upper and lower moulds, the models of the upper and lower moulds must be the same, and the fixing sleeve of the upper mould must be tightened. major Rack punching machine When placing the lower die, pay attention to the upward direction of the knife edge (the end with a small aperture), and do not damage the machine by installing it. Do not remove the quick coupler when the system has working pressure during operation. The screw rod and nut shall be lubricated with oil.

Don't just look at the price, but consider the manufacturing process of CNC punching machines from the perspective of quality and cycle, which can be roughly divided into ten categories. The climbing frame punching machine is based on different requirements of part materials, physical and chemical properties, mechanical strength, dimensional accuracy, surface finish, service life, economy, etc, Guangdong Rack punching machine Select different types of dies to form. Some parts have special requirements when forming, and the CNC punching machine also needs to use advanced processes such as hot runner, gas assisted molding, cylinder, etc. major Rack punching machine In general, whether the machine tool has a blank holder mechanism, or even a side lubricant, multi station progressive, etc., should be considered for large stamping dies. The climbing frame punching machine should not only focus on product design, but also ignore the service life of the mold.

When the parts of the pipe punching machine are working, under the rated working conditions, they will not be damaged in any form, nor will they produce residual deformation beyond the allowable limit, and can ensure the normal operation and work of the machine, so it is considered that the parts meet the strength requirements. Guangdong Rack punching machine In design, most important parts are checked by strength conditions (relevant strength theory in engineering mechanics), except some parts with small force or complex shape that cannot be calculated are determined by experience and experiments. major Rack punching machine If the strength of the parts is not enough, the overall fracture, surface contact fatigue or plastic deformation and other failures will occur and the working ability will be lost, so the strength requirements must be met when designing the parts.

The hydraulic high-speed punching machine is widely used for punching stainless steel (aluminum alloy) profiles, fan factories, air conditioning accessory factories, antenna factories and other hardware. Automatic and semi-automatic equipment can be customized. Guangdong Rack punching machine Anti theft net punching equipment, anti-theft window punching, protective window punching machine, anti-theft net equipment factory stainless steel anti-theft net hydraulic punching machine is your choice! The anti-theft net punching machine has a positioning rod with a scale, which is convenient for direct reading, accurate positioning, flat punching, etc, major Rack punching machine It can adjust the perforation and single face at will. It is an ideal punching equipment for anti-theft net, guardrail and shelf

First, observe the safety operation regulations of the numerical control punching machine. When the punching equipment is in place, the chassis should be leveled and stabilized. The punching frame should be vertical, and grounding protection should be done according to the construction power requirements. secondly, Guangdong Rack punching machine Price Before starting work, carefully check whether each component is properly configured and whether the fastening part is loose. If there is any abnormality, timely and correctly handle it. Numerically controlled punching machines are usually equipped with a variety of protective devices, Rack punching machine Before starting operation, make sure that these protective devices can work normally, which can improve the safety protection performance of the NC punching machine during operation and effectively reduce the accident rate during operation. In addition, the operator shall wear all kinds of armor as required, clean up the sundries on the machine table and within a certain range around, and irrelevant personnel shall not be close to the working area when the punching machine is running.