Science and technology bring convenience to people, improve work efficiency and increase income. The CNC climbing frame punching machine is a fast punching equipment independently developed by Jinhai, which can be used for punching C-shaped steel, square steel and channel steel. Heilongjiang Semi automatic hydraulic punching machine manufactor It is widely used in mining, tunnel, construction engineering and other fields. Compared with the same type of products on the market, Semi automatic hydraulic punching machine This product improves the punching precision and speed, and is suitable for two feed servo motors, imported hydraulic oil pump, contact phone of climbing frame automatic punching machine, PLC operating system, and can also match a variety of molds, achieving a true sense of "multi-function". The CNC climbing frame full-automatic punching machine works better together with the special die produced by Yinjiang, bringing infinite convenience to new and old users.

First, observe the safety operation regulations of the numerical control punching machine. When the punching equipment is in place, the chassis should be leveled and stabilized. The punching frame should be vertical, and grounding protection should be done according to the construction power requirements. secondly, Heilongjiang Semi automatic hydraulic punching machine manufactor Before starting work, carefully check whether each component is properly configured and whether the fastening part is loose. If there is any abnormality, timely and correctly handle it. Numerically controlled punching machines are usually equipped with a variety of protective devices, Semi automatic hydraulic punching machine Before starting operation, make sure that these protective devices can work normally, which can improve the safety protection performance of the NC punching machine during operation and effectively reduce the accident rate during operation. In addition, the operator shall wear all kinds of armor as required, clean up the sundries on the machine table and within a certain range around, and irrelevant personnel shall not be close to the working area when the punching machine is running.

Once the NC climbing frame punching machine breaks down, its working efficiency will be seriously affected. If it is operated improperly, it will also have a more fatal impact on the life of the equipment. Heilongjiang Semi automatic hydraulic punching machine manufactor Using NC punching machine strictly according to standards can not only improve efficiency, but also extend service life. Determine whether your equipment is multi station or single station. Let's talk about the multi station CNC punching machine, Semi automatic hydraulic punching machine When in use, only one oil circuit switch can be opened for operation at a time, and multiple oil circuit switches cannot be opened at the same time. Many people will use multiple switches simultaneously to improve efficiency, which will have a bad impact on equipment operation and processing quality.

The ordinary pipe punching machine has no automatic positioning system, which is equivalent to a small punching machine that solves the feeding problem. Automatic pipe punching machine adds automatic positioning system on the basis of ordinary pipe punching machine, Heilongjiang Semi automatic hydraulic punching machine manufactor It greatly improves the precision and speed of punching, which can be understood as an automatic controlled high-precision small punch. The automatic pipe punching machine can not only position itself, but also automatically feed materials in batches, greatly saving manpower. The hydraulic automatic pipe punching machine produced by our factory adopts large torque AC synchronous servo motor, Semi automatic hydraulic punching machine It is characterized by fast response, high positioning accuracy, low noise, small brake heat loss and long service life. Motion control: professional PLC controller, touch screen operation, simple and convenient.

Once the pipe rack punching machine contacts the water source, it is easy for the machine to break down, so the enterprise should ensure that the equipment can stay away from the water source and maintain a dry environment. If the water ingress at the solenoid valve is more serious, Heilongjiang major Semi automatic hydraulic punching machine Parts may rust and cannot be used normally. Besides, the moist substances in the air will also damage the system elements, so it is necessary to ensure that the compressed air of the equipment is always dry. Only in this way can we effectively avoid machine failures and increase maintenance costs, and give full play to the advantages of high accuracy and efficiency of equipment. When using the pipe punching machine, the enterprise should also let the staff carefully check the equipment parts exposed to the air. Semi automatic hydraulic punching machine Once any abnormality is found, the operation should be stopped, and the operation should be restarted after troubleshooting. This can effectively protect the equipment from damage and extend its life to provide quality services for enterprises.

With the arrival of the automation era, the use of CNC thick wall pipe punching machines has become more and more common. However, in the process of using the punching machine, we should first pay attention to safety production. The site where the stainless steel punching machine is used should remove obstacles such as hole locations and surrounding stones according to the requirements of the punching machine instructions. Heilongjiang Semi automatic hydraulic punching machine manufactor The distance from the operation site to the power transformer or power supply trunk line shall be within 200m, and the voltage drop during startup shall not exceed 10% of the rated voltage. The motor and control box shall have good grounding device. Before installation, Semi automatic hydraulic punching machine Check and confirm that the punch bar and all parts are free of deformation; After installation, the allowable deviation of the center line between the punch and the power head is 1% of the total length.