The ordinary pipe punching machine has no automatic positioning system, which is equivalent to a small punching machine that solves the feeding problem. Automatic pipe punching machine adds automatic positioning system on the basis of ordinary pipe punching machine, Shaanxi Rack punching machine manufactor It greatly improves the precision and speed of punching, which can be understood as an automatic controlled high-precision small punch. The automatic pipe punching machine can not only position itself, but also automatically feed materials in batches, greatly saving manpower. The hydraulic automatic pipe punching machine produced by our factory adopts large torque AC synchronous servo motor, Rack punching machine It is characterized by fast response, high positioning accuracy, low noise, small brake heat loss and long service life. Motion control: professional PLC controller, touch screen operation, simple and convenient.

First, observe the safety operation regulations of the numerical control punching machine. When the punching equipment is in place, the chassis should be leveled and stabilized. The punching frame should be vertical, and grounding protection should be done according to the construction power requirements. secondly, Shaanxi Rack punching machine manufactor Before starting work, carefully check whether each component is properly configured and whether the fastening part is loose. If there is any abnormality, timely and correctly handle it. Numerically controlled punching machines are usually equipped with a variety of protective devices, Rack punching machine Before starting operation, make sure that these protective devices can work normally, which can improve the safety protection performance of the NC punching machine during operation and effectively reduce the accident rate during operation. In addition, the operator shall wear all kinds of armor as required, clean up the sundries on the machine table and within a certain range around, and irrelevant personnel shall not be close to the working area when the punching machine is running.

In order to ensure that the round pipe punching machine has good quality and use effect, it is recommended that enterprises choose genuine hydraulic oil with relatively high cost performance. Because the hydraulic oil with good brand has high purity and less impurities, it will not be worn by impurities after being used for the round pipe punching machine, and the oil is not easy to deteriorate, Shaanxi Rack punching machine Can play a better role. As the hydraulic system is an important part of the pipe punching machine, and the hydraulic oil plays a crucial role in it, purchase Rack punching machine When using the round pipe punching machine, enterprises should not only use the equipment according to the operating rules, but also pay attention to adding and replacing the hydraulic oil in the hydraulic system regularly to ensure that the quality and life of the round pipe punching machine will not be affected.

If the round pipe punching machine used by the enterprise has the specified special hydraulic oil, the special hydraulic oil should be used according to the requirements instead of mixing with other types of hydraulic oil. Shaanxi purchase Rack punching machine If the round pipe punching machine does not have the specified hydraulic oil, the appropriate hydraulic oil brand can be selected according to the working environment and working conditions of the hydraulic system. After selecting the type of hydraulic oil, the enterprise must also determine the viscosity of the hydraulic oil required by the pipe punching machine. Rack punching machine The viscosity should be selected according to the temperature range of the geographical location. Generally speaking, the thinner hydraulic oil can be used in the northern region, and the hydraulic oil with a slightly higher viscosity can be used in the southern region. Because the temperature in the north is low, if the viscosity of the hydraulic oil is high, it is not conducive to the operation of the hydraulic system in the low temperature environment.

The normal CNC punching machine can customize the operation procedure of the product according to the customer's product requirements, Shaanxi Rack punching machine And the whole process does not require professional computer personnel to program. The CNC punching machine has specially designed a humanized human-computer interactive operation screen. The operator only needs to input the required punching hole diameter, punching hole position, thickness and other variables, and then just wait and observe whether the equipment is in good condition. The CNC punching machine adopts the domestic double vane pump as the main component equipment of its bearings, purchase Rack punching machine Compared with the traditional pump, this equipment has the characteristics of low noise, high efficiency, large flow and long service life. At the same time, the high-quality CNC punching machine is specially equipped with a high-quality cooling system to ensure the smooth and efficient operation of the equipment.