上海龙凤1314

Welcome to the official website of Foshan Jinhai CNC Machinery Co., Ltd!

 WeChat picture_20210420135910.png

 Rack punching machine
Your current location: home page > Hot information

Which one is better to purchase zinc steel guardrail CNC punching machine in Zhengzhou

2022-06-06
 Which one is better to purchase zinc steel guardrail CNC punching machine in Zhengzhou

During commissioning, it is not necessary to feed materials, but it is necessary to first raise the guide screw on the guide plate, and then gradually adjust the ram of the punch to the bottom dead center by inching. It is necessary to pay special attention to that the guide plate should not press the floating rod too low, otherwise the floating rod will be bent or broken. purchase Numerical control punching machine for zinc steel guardrail Which one is good When starting the punching machine for continuous punching, it is necessary to rotate the speed adjusting screw of the nc servo feeder clockwise. The slider moves slightly slowly, so that it can be seen whether the slider touches the nylon gasket and the length adjusting screw when it moves back and forth. Numerical control punching machine for zinc steel guardrail If the full-automatic punching machine only touches the length adjusting screw but not the nylon gasket when the sliding block moves back and forth, it is because the floating rod is lowered too deep, and the guide screw on the punching machine needs to be gradually raised.

 Which one is better to purchase zinc steel guardrail CNC punching machine in Zhengzhou

First, observe the safety operation regulations of the numerical control punching machine. When the punching equipment is in place, the chassis should be leveled and stabilized. The punching frame should be vertical, and grounding protection should be done according to the construction power requirements. secondly, Zhengzhou Numerical control punching machine for zinc steel guardrail Which one is good Before starting work, carefully check whether each component is properly configured and whether the fastening part is loose. If there is any abnormality, timely and correctly handle it. Numerically controlled punching machines are usually equipped with a variety of protective devices, Numerical control punching machine for zinc steel guardrail Before starting operation, make sure that these protective devices can work normally, which can improve the safety protection performance of the NC punching machine during operation and effectively reduce the accident rate during operation. In addition, the operator shall wear all kinds of armor as required, clean up the sundries on the machine table and within a certain range around, and irrelevant personnel shall not be close to the working area when the punching machine is running.

 Which one is better to purchase zinc steel guardrail CNC punching machine in Zhengzhou

The conveying precision of the feeder of the new construction climbing frame punch is relatively high, Zhengzhou Numerical control punching machine for zinc steel guardrail When working, directly input the length of the feeder to achieve accurate realization and the required step distance. CNC punch feeder can be transformed into multi section feeding according to customer needs, saving energy. Numerical control punching machine for zinc steel guardrail Which one is good The CNC punch feeder has good safety performance, which can avoid accidents, reduce the labor intensity of workers, and create greater economic benefits.

 Which one is better to purchase zinc steel guardrail CNC punching machine in Zhengzhou

The ordinary pipe punching machine has no automatic positioning system, which is equivalent to a small punching machine that solves the feeding problem. Automatic pipe punching machine adds automatic positioning system on the basis of ordinary pipe punching machine, Zhengzhou Numerical control punching machine for zinc steel guardrail Which one is good It greatly improves the precision and speed of punching, which can be understood as an automatic controlled high-precision small punch. The automatic pipe punching machine can not only position itself, but also automatically feed materials in batches, greatly saving manpower. The hydraulic automatic pipe punching machine produced by our factory adopts large torque AC synchronous servo motor, Numerical control punching machine for zinc steel guardrail It is characterized by fast response, high positioning accuracy, low noise, small brake heat loss and long service life. Motion control: professional PLC controller, touch screen operation, simple and convenient.

 Zinc steel guardrail punching machine

 1.png Mobile: 13679829857

 3.png Email: [email protected]

 4.png Address: Workshop 2, Baishaqiao Second Industrial Zone, Shishan, Nanhai District, Foshan City





Main business area: Guangdong Guangzhou Foshan Shenzhen Dongguan Zhongshan Zhuhai Huizhou Wuhan Shanghai