When punching with the climbing frame punching machine, the die shall be installed and inserted into the pipe for punching. It is strictly prohibited to empty punch when there is no pipe, otherwise the die will be damaged, Shijiazhuang Semi automatic hydraulic punching machine When punching full holes, if there is no punching, it will automatically return. Please move the lower proximity switch downward to protect the mold. In addition, it should be noted that the CNC climbing frame punching machine needs inspection and maintenance after running for a period of time. Check whether the blade of the punching needle has been passivated. If it has been passivated, please remove the punching needle and grind it, or purchase a new punching needle from the climbing frame punching machine manufacturer. In winter, the temperature becomes low. To protect the equipment, Semi automatic hydraulic punching machine Price If necessary, the engine should be started up and run idle for a period of time to warm up; If the equipment operates for a long time, check the temperature of the equipment. The temperature of the hydraulic oil should be controlled between 30 and 60 ℃.

The maintenance of the hydraulic rack punching machine can greatly delay the reduction of the accuracy of the hydraulic punching machine and extend its service life. The reduction of hydraulic punching machine precision is mainly manifested in the wear and plastic deformation of punching machine parts. Shijiazhuang Semi automatic hydraulic punching machine Price Therefore, the lack of maintenance is one of the reasons why the accuracy of the NC punching machine is reduced. You can combine your own situation to see whether this is the reason for the reduction in accuracy. The movement relationship (time and movement) between components is damaged due to grinding and deformation of components, purchase Semi automatic hydraulic punching machine It will also reduce the accuracy of the hydraulic rack punching machine. Numerous practical experiences have proved that the accuracy of hydraulic punching machines without maintenance or improper maintenance can reduce much faster than that of well maintained hydraulic punching machines.

During commissioning, it is not necessary to feed materials, but it is necessary to first raise the guide screw on the guide plate, and then gradually adjust the ram of the punch to the bottom dead center by inching. It is necessary to pay special attention to that the guide plate should not press the floating rod too low, otherwise the floating rod will be bent or broken. purchase Semi automatic hydraulic punching machine Price When starting the punching machine for continuous punching, it is necessary to rotate the speed adjusting screw of the nc servo feeder clockwise. The slider moves slightly slowly, so that it can be seen whether the slider touches the nylon gasket and the length adjusting screw when it moves back and forth. Semi automatic hydraulic punching machine If the full-automatic punching machine only touches the length adjusting screw but not the nylon gasket when the sliding block moves back and forth, it is because the floating rod is lowered too deep, and the guide screw on the punching machine needs to be gradually raised.

Energy saving and environmental protection, less noise, faster working efficiency than ordinary punches, small footprint, safe and secure operation. Shijiazhuang Semi automatic hydraulic punching machine Price The punching needle is specially designed, and the time for changing the mold is short. Time delay protection circuit. When nobody operates the machine, the time delay protection switch will automatically enter the standby state. If you want to start work, you need to turn on the circuit switch again. The punching machine for handrail shelf of guardrail stairs is widely used in punching stainless steel, aluminum alloy bathroom, color steel, zinc steel guardrails, and is the equipment with fast pipe punching processing at present. Guardrail stair handrail punching machine can be customized to multiple working positions, easy and convenient to disassemble the mold, durable mold, easy for novices to use and so on. Semi automatic hydraulic punching machine It can debug and punch half hole or full hole at will, with flat punching and accurate positioning. It can also produce various new anti-theft nets (diamond anti-theft net, round tube square tube anti-theft net, door flower, etc.), and provide one-year warranty service for the whole machine.

We often consider what numerical control mechanical equipment is the ideal of the mechanical industry. purchase Semi automatic hydraulic punching machine High degree of automation control; The NC punching machine with high degree of automation has become a good helper for pipe processing enterprises. Employees only need to master some key data, Shijiazhuang Semi automatic hydraulic punching machine Price And these devices are usually simple to operate, fast and efficient. CNC punching machine has high cost performance ratio; At present, there are few enterprises that can really reach this standard, because some enterprises in the NC punching machine industry only care about the price, and do not care about product quality and after-sales.