The ordinary pipe punching machine has no automatic positioning system, which is equivalent to a small punching machine that solves the feeding problem. Automatic pipe punching machine adds automatic positioning system on the basis of ordinary pipe punching machine, Zhongshan Rack punching machine manufactor It greatly improves the precision and speed of punching, which can be understood as an automatic controlled high-precision small punch. The automatic pipe punching machine can not only position itself, but also automatically feed materials in batches, greatly saving manpower. The hydraulic automatic pipe punching machine produced by our factory adopts large torque AC synchronous servo motor, Rack punching machine It is characterized by fast response, high positioning accuracy, low noise, small brake heat loss and long service life. Motion control: professional PLC controller, touch screen operation, simple and convenient.

First, observe the safety operation regulations of the numerical control punching machine. When the punching equipment is in place, the chassis should be leveled and stabilized. The punching frame should be vertical, and grounding protection should be done according to the construction power requirements. secondly, Zhongshan Rack punching machine manufactor Before starting work, carefully check whether each component is properly configured and whether the fastening part is loose. If there is any abnormality, timely and correctly handle it. Numerically controlled punching machines are usually equipped with a variety of protective devices, Rack punching machine Before starting operation, make sure that these protective devices can work normally, which can improve the safety protection performance of the NC punching machine during operation and effectively reduce the accident rate during operation. In addition, the operator shall wear all kinds of armor as required, clean up the sundries on the machine table and within a certain range around, and irrelevant personnel shall not be close to the working area when the punching machine is running.

If the round pipe punching machine used by the enterprise has the specified special hydraulic oil, the special hydraulic oil should be used according to the requirements instead of mixing with other types of hydraulic oil. Zhongshan major Rack punching machine If the round pipe punching machine does not have the specified hydraulic oil, the appropriate hydraulic oil brand can be selected according to the working environment and working conditions of the hydraulic system. After selecting the type of hydraulic oil, the enterprise must also determine the viscosity of the hydraulic oil required by the pipe punching machine. Rack punching machine The viscosity should be selected according to the temperature range of the geographical location. Generally speaking, the thinner hydraulic oil can be used in the northern region, and the hydraulic oil with a slightly higher viscosity can be used in the southern region. Because the temperature in the north is low, if the viscosity of the hydraulic oil is high, it is not conducive to the operation of the hydraulic system in the low temperature environment.

Energy saving and environmental protection, less noise, faster working efficiency than ordinary punches, small footprint, safe and secure operation. Zhongshan Rack punching machine manufactor The punching needle is specially designed, and the time for changing the mold is short. Time delay protection circuit. When nobody operates the machine, the time delay protection switch will automatically enter the standby state. If you want to start work, you need to turn on the circuit switch again. The punching machine for handrail shelf of guardrail stairs is widely used in punching stainless steel, aluminum alloy bathroom, color steel, zinc steel guardrails, and is the equipment with fast pipe punching processing at present. Guardrail stair handrail punching machine can be customized to multiple working positions, easy and convenient to disassemble the mold, durable mold, easy for novices to use and so on. Rack punching machine It can debug and punch half hole or full hole at will, with flat punching and accurate positioning. It can also produce various new anti-theft nets (diamond anti-theft net, round tube square tube anti-theft net, door flower, etc.), and provide one-year warranty service for the whole machine.

During the test run of the full-automatic punching machine, the sliding block moves back and forth. If the stainless steel pipe fence punching machine only touches the nylon gasket and does not touch the length adjustment screw, it is because the floating rod can not be lowered deep, and the guide screw on the punching machine needs to be gradually adjusted downward. major Rack punching machine manufactor The hydraulic high-speed punching machine is widely used in stainless steel (zinc steel, aluminum alloy, steel pipe, welded pipe, seamless pipe, square pipe, round pipe, flat iron, channel steel, angle iron) profiles, fan factories, air conditioning parts factories, antenna factories, shelf factories, metal furniture factories, automobile parts factories Zhongshan Rack punching machine Building materials manufacturers and other hardware pipe fittings, profiles punching processing. Automatic and semi-automatic equipment can be customized according to customer requirements.

The normal CNC punching machine can customize the operation procedure of the product according to the customer's product requirements, Zhongshan Rack punching machine And the whole process does not require professional computer personnel to program. The CNC punching machine has specially designed a humanized human-computer interactive operation screen. The operator only needs to input the required punching hole diameter, punching hole position, thickness and other variables, and then just wait and observe whether the equipment is in good condition. The CNC punching machine adopts the domestic double vane pump as the main component equipment of its bearings, major Rack punching machine Compared with the traditional pump, this equipment has the characteristics of low noise, high efficiency, large flow and long service life. At the same time, the high-quality CNC punching machine is specially equipped with a high-quality cooling system to ensure the smooth and efficient operation of the equipment.