First, observe the safety operation regulations of the numerical control punching machine. When the punching equipment is in place, the chassis should be leveled and stabilized. The punching frame should be vertical, and grounding protection should be done according to the construction power requirements. secondly, Huizhou Auto punching machine manufactor Before starting work, carefully check whether each component is properly configured and whether the fastening part is loose. If there is any abnormality, timely and correctly handle it. Numerically controlled punching machines are usually equipped with a variety of protective devices, Auto punching machine Before starting operation, make sure that these protective devices can work normally, which can improve the safety protection performance of the NC punching machine during operation and effectively reduce the accident rate during operation. In addition, the operator shall wear all kinds of armor as required, clean up the sundries on the machine table and within a certain range around, and irrelevant personnel shall not be close to the working area when the punching machine is running.

Pipe automatic punching machine processing enterprises have been looking for a more suitable punching equipment with various functions. The high-quality Jinhai Mechanical CNC punching machine can automatically switch the working mode of double-sided hole and single-sided hole punching, Huizhou major Auto punching machine At the same time, it can also realize punching processing of pipes, angle iron flat iron, channel steel groove aluminum and other profiles on the same machine, Auto punching machine This has also saved a lot of equipment costs for enterprises and greatly increased the efficiency of production and processing to a certain extent.

Use the numerical control zinc steel fence punching machine. The equipment is accurate and fast, with excellent product effect, simple and convenient operation and long service life, Huizhou major Auto punching machine It is the best choice for pipe punching. However, no matter how good the machine is, it also needs to pay attention to daily maintenance in order to make it perform to a large extent. The working fluid shall be replaced once a year, and the replacement time shall not exceed three months. Auto punching machine manufactor The sliding block shall be filled with lubricating oil frequently, the exposed surface of the column shall be kept clean frequently, and oil shall be sprayed before each work. If the machine is out of service for a long time, the surface should be cleaned and coated with antirust oil. The pressure gauge shall be calibrated and checked every six months.

In order to ensure that the round pipe punching machine has good quality and use effect, it is recommended that enterprises choose genuine hydraulic oil with relatively high cost performance. Because the hydraulic oil with good brand has high purity and less impurities, it will not be worn by impurities after being used for the round pipe punching machine, and the oil is not easy to deteriorate, Huizhou Auto punching machine Can play a better role. As the hydraulic system is an important part of the pipe punching machine, and the hydraulic oil plays a crucial role in it, major Auto punching machine When using the round pipe punching machine, enterprises should not only use the equipment according to the operating rules, but also pay attention to adding and replacing the hydraulic oil in the hydraulic system regularly to ensure that the quality and life of the round pipe punching machine will not be affected.

Science and technology bring convenience to people, improve work efficiency and increase income. The CNC climbing frame punching machine is a fast punching equipment independently developed by Jinhai, which can be used for punching C-shaped steel, square steel and channel steel. Huizhou Auto punching machine manufactor It is widely used in mining, tunnel, construction engineering and other fields. Compared with the same type of products on the market, Auto punching machine This product improves the punching precision and speed, and is suitable for two feed servo motors, imported hydraulic oil pump, contact phone of climbing frame automatic punching machine, PLC operating system, and can also match a variety of molds, achieving a true sense of "multi-function". The CNC climbing frame full-automatic punching machine works better together with the special die produced by Yinjiang, bringing infinite convenience to new and old users.

Pay attention to the operating condition of the equipment when starting the square pipe punching machine, Huizhou Auto punching machine In case of abnormal noise and displacement, the square tube punching machine shall be shut down in time, and fault diagnosis and maintenance shall be carried out. Since the clamping and separating action of the pneumatic part of the professional square pipe punching machine requires high flexibility, major Auto punching machine When in use, not only should the pneumatic part be checked regularly to see whether it can be sucked and pulled freely, but also should pay attention to whether there is air leakage in the square tube punching machine.