For CNC punching machine equipment, quality is the hard truth for enterprises to survive. Therefore, we must ensure the stability of product quality. Equipment and materials of CNC punching machine; Due to the increased cost of current materials, Changsha Stainless steel CNC punching machine Which one is good Some enterprises will start with raw materials and choose inferior materials to replace them. The result is that the product quality is not guaranteed. Before using the automatic CNC punching machine, be sure to check whether there are sundries at the punch and the lower die edge. Add lubricating oil to the upper and lower moving parts of the punch. Stainless steel CNC punching machine During use, keep the oiling part of the numerical control punching machine free of oil shortage. At the same time, it should be noted that after the use of the NC punching machine is completed, the NC punching machine should be cleaned first, and the punch should be pressed down to the low position to better protect the NC punching machine.

The lubrication function of the pipe punching machine will be gradually weakened after long-term use, which will lead to increased friction and damage in the process of equipment operation. Even professional pipe punching machines are not immune, Changsha Stainless steel CNC punching machine Therefore, in order to avoid this kind of situation, it is necessary to add lubricant in time, especially the position of the punch to maintain lubrication, reduce friction and extend the service life of the equipment. The pipe punching machine is the most taboo to be impacted by foreign objects. Even if the impact degree is not large, component failure is likely to occur. Stainless steel CNC punching machine Which one is good Therefore, whether before or after use, check whether there is any foreign matter between the punch and the lower die, and use carefully to prevent the punch from being damaged due to the extrusion of the punch and the lower die caused by foreign matters.

In the past, the traditional punching machine usually used manual or semi-automatic punching to finish punching the workpiece. Now, with the continuous progress of punching machine technology, some shortcomings of the former manual punching machine itself are more and more obvious, Changsha Stainless steel CNC punching machine Which one is good The speed is very slow, so the efficiency is very low. If it is semi-automatic, automatic feeding cannot be carried out. CNC climbing frame punching machine needs frequent maintenance to ensure its life; Before operation, check whether the punch and die of the numerical control punching machine are matched, otherwise the punching machine host will be damaged. When assembling the upper and lower moulds, the models of the upper and lower moulds must be the same, and the fixing sleeve of the upper mould must be tightened. major Stainless steel CNC punching machine When placing the lower die, pay attention to the upward direction of the knife edge (the end with a small aperture), and do not damage the machine by installing it. Do not remove the quick coupler when the system has working pressure during operation. The screw rod and nut shall be lubricated with oil.

In order to ensure the flexibility of the pipe punching machine, Changsha Stainless steel CNC punching machine Which one is good The sliding block also needs to be often injected with lubricating oil. Generally, before the pipe punching machine runs, it needs to be injected with oil. The column surface of the pipe punching machine also needs to be clean. If the pipe punching machine has not been used for a long time Changsha Stainless steel CNC punching machine The surface shall be cleaned and coated with antirust oil to avoid corrosion and rust. The pipe punching machine should also be checked regularly, and the pressure gauge should be checked once every 6 months.

Once the NC climbing frame punching machine breaks down, its working efficiency will be seriously affected. If it is operated improperly, it will also have a more fatal impact on the life of the equipment. Changsha Stainless steel CNC punching machine Which one is good Using NC punching machine strictly according to standards can not only improve efficiency, but also extend service life. Determine whether your equipment is multi station or single station. Let's talk about the multi station CNC punching machine, Stainless steel CNC punching machine When in use, only one oil circuit switch can be opened for operation at a time, and multiple oil circuit switches cannot be opened at the same time. Many people will use multiple switches simultaneously to improve efficiency, which will have a bad impact on equipment operation and processing quality.

With the continuous development of China's manufacturing industry, the technical level of punching machines and other equipment is required to be higher and higher. The requirements of the market for equipment determine that punching machine manufacturers should constantly improve the technical level of their products. Rack punching machine manufacturers should follow the market development and produce high-end punching equipment, Changsha major Stainless steel CNC punching machine With the help of the intelligent trend of the development of China's machine tool industry, the punching machine technology is brought to a higher level. In addition, Stainless steel CNC punching machine When punching, after the mold is installed, insert the pipe for punching. It is strictly prohibited to empty punch when there is no pipe, otherwise the mold will be damaged. When punching the full hole, if there is no punching, it will automatically return. Please move the lower proximity switch downward to protect the mold.