With the arrival of the automation era, the use of CNC thick wall pipe punching machines has become more and more common. However, in the process of using the punching machine, we should first pay attention to safety production. The site where the stainless steel punching machine is used should remove obstacles such as hole locations and surrounding stones according to the requirements of the punching machine instructions. Huizhou Rack punching machine manufactor The distance from the operation site to the power transformer or power supply trunk line shall be within 200m, and the voltage drop during startup shall not exceed 10% of the rated voltage. The motor and control box shall have good grounding device. Before installation, Rack punching machine Check and confirm that the punch bar and all parts are free of deformation; After installation, the allowable deviation of the center line between the punch and the power head is 1% of the total length.

When punching with the climbing frame punching machine, the die shall be installed and inserted into the pipe for punching. It is strictly prohibited to empty punch when there is no pipe, otherwise the die will be damaged, Huizhou Rack punching machine When punching full holes, if there is no punching, it will automatically return. Please move the lower proximity switch downward to protect the mold. In addition, it should be noted that the CNC climbing frame punching machine needs inspection and maintenance after running for a period of time. Check whether the blade of the punching needle has been passivated. If it has been passivated, please remove the punching needle and grind it, or purchase a new punching needle from the climbing frame punching machine manufacturer. In winter, the temperature becomes low. To protect the equipment, Rack punching machine manufactor If necessary, the engine should be started up and run idle for a period of time to warm up; If the equipment operates for a long time, check the temperature of the equipment. The temperature of the hydraulic oil should be controlled between 30 and 60 ℃.

The normal CNC punching machine can customize the operation procedure of the product according to the customer's product requirements, Huizhou Rack punching machine And the whole process does not require professional computer personnel to program. The CNC punching machine has specially designed a humanized human-computer interactive operation screen. The operator only needs to input the required punching hole diameter, punching hole position, thickness and other variables, and then just wait and observe whether the equipment is in good condition. The CNC punching machine adopts the domestic double vane pump as the main component equipment of its bearings, purchase Rack punching machine Compared with the traditional pump, this equipment has the characteristics of low noise, high efficiency, large flow and long service life. At the same time, the high-quality CNC punching machine is specially equipped with a high-quality cooling system to ensure the smooth and efficient operation of the equipment.

This model is equipped with two punching cylinders, which can be used for punching single or multiple cylinders respectively. The upper cylinder can be adjusted to punch half or full holes. The climbing frame automatic punching machine is easy to operate, superior in quality and reasonable in price, Huizhou Rack punching machine It meets the quality requirements of domestic and foreign markets, and can process high-quality and high-precision workpieces. The punching hole of this machine is flat without burrs, and the positioning is accurate. The clamping, lifting and other mechanisms of the whole machine are controlled by air pressure or hydraulic pressure. The positioning of workpieces (X, Y coordinates) is driven by servo, and the control of the whole machine is controlled by microcomputer, Rack punching machine manufactor Parameter setting and operation switching are performed through the touch screen interface, which is simple and convenient to operate, and can store more than 100 product processing parameters.

During commissioning, it is not necessary to feed materials, but it is necessary to first raise the guide screw on the guide plate, and then gradually adjust the ram of the punch to the bottom dead center by inching. It is necessary to pay special attention to that the guide plate should not press the floating rod too low, otherwise the floating rod will be bent or broken. purchase Rack punching machine manufactor When starting the punching machine for continuous punching, it is necessary to rotate the speed adjusting screw of the nc servo feeder clockwise. The slider moves slightly slowly, so that it can be seen whether the slider touches the nylon gasket and the length adjusting screw when it moves back and forth. Rack punching machine If the full-automatic punching machine only touches the length adjusting screw but not the nylon gasket when the sliding block moves back and forth, it is because the floating rod is lowered too deep, and the guide screw on the punching machine needs to be gradually raised.

For CNC punching machine equipment, quality is the hard truth for enterprises to survive. Therefore, we must ensure the stability of product quality. Equipment and materials of CNC punching machine; Due to the increased cost of current materials, Huizhou Rack punching machine manufactor Some enterprises will start with raw materials and choose inferior materials to replace them. The result is that the product quality is not guaranteed. Before using the automatic CNC punching machine, be sure to check whether there are sundries at the punch and the lower die edge. Add lubricating oil to the upper and lower moving parts of the punch. Rack punching machine During use, keep the oiling part of the numerical control punching machine free of oil shortage. At the same time, it should be noted that after the use of the NC punching machine is completed, the NC punching machine should be cleaned first, and the punch should be pressed down to the low position to better protect the NC punching machine.