During commissioning, it is not necessary to feed materials, but it is necessary to first raise the guide screw on the guide plate, and then gradually adjust the ram of the punch to the bottom dead center by inching. It is necessary to pay special attention to that the guide plate should not press the floating rod too low, otherwise the floating rod will be bent or broken. purchase Guardrail punching machine Price When starting the punching machine for continuous punching, it is necessary to rotate the speed adjusting screw of the nc servo feeder clockwise. The slider moves slightly slowly, so that it can be seen whether the slider touches the nylon gasket and the length adjusting screw when it moves back and forth. Guardrail punching machine If the full-automatic punching machine only touches the length adjusting screw but not the nylon gasket when the sliding block moves back and forth, it is because the floating rod is lowered too deep, and the guide screw on the punching machine needs to be gradually raised.

The automatic punching machine has beautiful appearance, reasonable and simple structure, and is easy to operate, Shenzhen Guardrail punching machine Price In this way, the cost of training staff can be saved, and the accuracy of the automatic punching machine is high. The climbing frame automatic punching machine agent is not easy to make mistakes, purchase Guardrail punching machine Even the most rigorous operation can be completed accurately. The operation screen of the automatic punching machine is a 7-inch touch screen, which is convenient for operation. The automatic punching machine adopts hydraulic and mechanical structure, with stable physical performance and strong adaptability.

Pay attention to the operating condition of the equipment when starting the square pipe punching machine, Shenzhen Guardrail punching machine In case of abnormal noise and displacement, the square tube punching machine shall be shut down in time, and fault diagnosis and maintenance shall be carried out. Since the clamping and separating action of the pneumatic part of the professional square pipe punching machine requires high flexibility, purchase Guardrail punching machine When in use, not only should the pneumatic part be checked regularly to see whether it can be sucked and pulled freely, but also should pay attention to whether there is air leakage in the square tube punching machine.

When punching with the climbing frame punching machine, the die shall be installed and inserted into the pipe for punching. It is strictly prohibited to empty punch when there is no pipe, otherwise the die will be damaged, Shenzhen Guardrail punching machine When punching full holes, if there is no punching, it will automatically return. Please move the lower proximity switch downward to protect the mold. In addition, it should be noted that the CNC climbing frame punching machine needs inspection and maintenance after running for a period of time. Check whether the blade of the punching needle has been passivated. If it has been passivated, please remove the punching needle and grind it, or purchase a new punching needle from the climbing frame punching machine manufacturer. In winter, the temperature becomes low. To protect the equipment, Guardrail punching machine Price If necessary, the engine should be started up and run idle for a period of time to warm up; If the equipment operates for a long time, check the temperature of the equipment. The temperature of the hydraulic oil should be controlled between 30 and 60 ℃.

Science and technology bring convenience to people, improve work efficiency and increase income. The CNC climbing frame punching machine is a fast punching equipment independently developed by Jinhai, which can be used for punching C-shaped steel, square steel and channel steel. Shenzhen Guardrail punching machine Price It is widely used in mining, tunnel, construction engineering and other fields. Compared with the same type of products on the market, Guardrail punching machine This product improves the punching precision and speed, and is suitable for two feed servo motors, imported hydraulic oil pump, contact phone of climbing frame automatic punching machine, PLC operating system, and can also match a variety of molds, achieving a true sense of "multi-function". The CNC climbing frame full-automatic punching machine works better together with the special die produced by Yinjiang, bringing infinite convenience to new and old users.

Use the numerical control zinc steel fence punching machine. The equipment is accurate and fast, with excellent product effect, simple and convenient operation and long service life, Shenzhen purchase Guardrail punching machine It is the best choice for pipe punching. However, no matter how good the machine is, it also needs to pay attention to daily maintenance in order to make it perform to a large extent. The working fluid shall be replaced once a year, and the replacement time shall not exceed three months. Guardrail punching machine Price The sliding block shall be filled with lubricating oil frequently, the exposed surface of the column shall be kept clean frequently, and oil shall be sprayed before each work. If the machine is out of service for a long time, the surface should be cleaned and coated with antirust oil. The pressure gauge shall be calibrated and checked every six months.