Science and technology bring convenience to people, improve work efficiency and increase income. The CNC climbing frame punching machine is a fast punching equipment independently developed by Jinhai, which can be used for punching C-shaped steel, square steel and channel steel. Huizhou Guardrail punching machine manufactor It is widely used in mining, tunnel, construction engineering and other fields. Compared with the same type of products on the market, Guardrail punching machine This product improves the punching precision and speed, and is suitable for two feed servo motors, imported hydraulic oil pump, contact phone of climbing frame automatic punching machine, PLC operating system, and can also match a variety of molds, achieving a true sense of "multi-function". The CNC climbing frame full-automatic punching machine works better together with the special die produced by Yinjiang, bringing infinite convenience to new and old users.

In order to ensure the flexibility of the pipe punching machine, Huizhou Guardrail punching machine manufactor The sliding block also needs to be often injected with lubricating oil. Generally, before the pipe punching machine runs, it needs to be injected with oil. The column surface of the pipe punching machine also needs to be clean. If the pipe punching machine has not been used for a long time Huizhou Guardrail punching machine The surface shall be cleaned and coated with antirust oil to avoid corrosion and rust. The pipe punching machine should also be checked regularly, and the pressure gauge should be checked once every 6 months.

The ordinary pipe punching machine has no automatic positioning system, which is equivalent to a small punching machine that solves the feeding problem. Automatic pipe punching machine adds automatic positioning system on the basis of ordinary pipe punching machine, Huizhou Guardrail punching machine manufactor It greatly improves the precision and speed of punching, which can be understood as an automatic controlled high-precision small punch. The automatic pipe punching machine can not only position itself, but also automatically feed materials in batches, greatly saving manpower. The hydraulic automatic pipe punching machine produced by our factory adopts large torque AC synchronous servo motor, Guardrail punching machine It is characterized by fast response, high positioning accuracy, low noise, small brake heat loss and long service life. Motion control: professional PLC controller, touch screen operation, simple and convenient.

Use the numerical control zinc steel fence punching machine. The equipment is accurate and fast, with excellent product effect, simple and convenient operation and long service life, Huizhou purchase Guardrail punching machine It is the best choice for pipe punching. However, no matter how good the machine is, it also needs to pay attention to daily maintenance in order to make it perform to a large extent. The working fluid shall be replaced once a year, and the replacement time shall not exceed three months. Guardrail punching machine manufactor The sliding block shall be filled with lubricating oil frequently, the exposed surface of the column shall be kept clean frequently, and oil shall be sprayed before each work. If the machine is out of service for a long time, the surface should be cleaned and coated with antirust oil. The pressure gauge shall be calibrated and checked every six months.

For CNC punching machine equipment, quality is the hard truth for enterprises to survive. Therefore, we must ensure the stability of product quality. Equipment and materials of CNC punching machine; Due to the increased cost of current materials, Huizhou Guardrail punching machine manufactor Some enterprises will start with raw materials and choose inferior materials to replace them. The result is that the product quality is not guaranteed. Before using the automatic CNC punching machine, be sure to check whether there are sundries at the punch and the lower die edge. Add lubricating oil to the upper and lower moving parts of the punch. Guardrail punching machine During use, keep the oiling part of the numerical control punching machine free of oil shortage. At the same time, it should be noted that after the use of the NC punching machine is completed, the NC punching machine should be cleaned first, and the punch should be pressed down to the low position to better protect the NC punching machine.

When purchasing a NC punching machine, some details need attention. A small detail that is not paid attention to may affect the service life of the NC punching machine. Here is a detail that is easy to be ignored, that is, the polishing of the machine's steel plate, purchase Guardrail punching machine manufactor Some people may think that as long as the mold is finished, there will be no problem. It is not important whether the steel plate is ground or not, but in fact, this is not the case. If the steel plate under the mold is not ground smoothly, Guardrail punching machine It is likely to affect the service life of the mold, so it is likely to fail in the future use process.