Science and technology bring convenience to people, improve work efficiency and increase income. The CNC climbing frame punching machine is a fast punching equipment independently developed by Jinhai, which can be used for punching C-shaped steel, square steel and channel steel. Shenzhen Guardrail CNC punching machine Which one is good It is widely used in mining, tunnel, construction engineering and other fields. Compared with the same type of products on the market, Guardrail CNC punching machine This product improves the punching precision and speed, and is suitable for two feed servo motors, imported hydraulic oil pump, contact phone of climbing frame automatic punching machine, PLC operating system, and can also match a variety of molds, achieving a true sense of "multi-function". The CNC climbing frame full-automatic punching machine works better together with the special die produced by Yinjiang, bringing infinite convenience to new and old users.

This model is equipped with two punching cylinders, which can be used for punching single or multiple cylinders respectively. The upper cylinder can be adjusted to punch half or full holes. The climbing frame automatic punching machine is easy to operate, superior in quality and reasonable in price, Shenzhen Guardrail CNC punching machine It meets the quality requirements of domestic and foreign markets, and can process high-quality and high-precision workpieces. The punching hole of this machine is flat without burrs, and the positioning is accurate. The clamping, lifting and other mechanisms of the whole machine are controlled by air pressure or hydraulic pressure. The positioning of workpieces (X, Y coordinates) is driven by servo, and the control of the whole machine is controlled by microcomputer, Guardrail CNC punching machine Which one is good Parameter setting and operation switching are performed through the touch screen interface, which is simple and convenient to operate, and can store more than 100 product processing parameters.

During commissioning, it is not necessary to feed materials, but it is necessary to first raise the guide screw on the guide plate, and then gradually adjust the ram of the punch to the bottom dead center by inching. It is necessary to pay special attention to that the guide plate should not press the floating rod too low, otherwise the floating rod will be bent or broken. purchase Guardrail CNC punching machine Which one is good When starting the punching machine for continuous punching, it is necessary to rotate the speed adjusting screw of the nc servo feeder clockwise. The slider moves slightly slowly, so that it can be seen whether the slider touches the nylon gasket and the length adjusting screw when it moves back and forth. Guardrail CNC punching machine If the full-automatic punching machine only touches the length adjusting screw but not the nylon gasket when the sliding block moves back and forth, it is because the floating rod is lowered too deep, and the guide screw on the punching machine needs to be gradually raised.

When the parts of the pipe punching machine are working, under the rated working conditions, they will not be damaged in any form, nor will they produce residual deformation beyond the allowable limit, and can ensure the normal operation and work of the machine, so it is considered that the parts meet the strength requirements. Shenzhen Guardrail CNC punching machine In design, most important parts are checked by strength conditions (relevant strength theory in engineering mechanics), except some parts with small force or complex shape that cannot be calculated are determined by experience and experiments. purchase Guardrail CNC punching machine If the strength of the parts is not enough, the overall fracture, surface contact fatigue or plastic deformation and other failures will occur and the working ability will be lost, so the strength requirements must be met when designing the parts.

The reason why the NC automatic punching machine for profiles is favored by a large number of manufacturers is due to its excellent performance characteristics. multi-function. The NC profile automatic punching machine can form multiple holes of any shape on pipes of any specification and material at one time, the pipe wall can be of any thickness, and the hole center distance can be adjusted at will. high-precision. Shenzhen purchase Guardrail CNC punching machine The punching machine is controlled by the NC programming program of the machining center, and the processed hole shape is flat and the center distance is accurate. Easy to operate. Guardrail CNC punching machine The whole machine is controlled by microcomputer, which is easy to operate and learn. Super efficient. The equipment can meet the requirements of a large number of openings in a unit time, and its efficiency is much higher than that of traditional punches.