At present, the first-class full-automatic punching machine for zinc steel guardrail has been widely used in our life. Jiangsu purchase Rack CNC punching machine Customers who often use full-automatic punching machines for zinc steel guardrails should know that because of the advantages of simple structure, easy operation, light weight, and convenient handling, the full-automatic punching machine has been used in many aspects, such as stainless steel, anti-theft net, aluminum alloy, etc. Pay attention to the grinding of the machine table steel plate. This is the key point. Customers should know that, Rack CNC punching machine The machine will produce varying degrees of "vibration" during operation, but people pay less attention to the looseness and wear of the mold and the underlying steel plate during the vibration process, but the problem comes out after a long time, so the customer must pay attention to the polishing of the table steel plate of the full-automatic punching machine.

In order to give better play to the performance of the pipe punching machine, what matters should be paid attention to when the pipe punching machine is used and when it is maintained later? The oil of the pipe punching machine needs to be replaced regularly, basically every year, Jiangsu purchase Rack CNC punching machine It should take less than three months, that is to say, it needs to be replaced within three months. Check whether there is any problem with the protective safety device, lubrication and other parts, and whether the relevant fastening screws are firm and loose. Rack CNC punching machine Which one is good When the mechanical operation is over, cut off the power supply and wipe the machine tool. In short, special attention should be paid to the daily use of the pipe punching machine, and regular inspection and maintenance should be carried out to ensure that the pipe punching machine can operate efficiently and normally.

Don't just look at the price, but consider the manufacturing process of CNC punching machines from the perspective of quality and cycle, which can be roughly divided into ten categories. The climbing frame punching machine is based on different requirements of part materials, physical and chemical properties, mechanical strength, dimensional accuracy, surface finish, service life, economy, etc, Jiangsu Rack CNC punching machine Select different types of dies to form. Some parts have special requirements when forming, and the CNC punching machine also needs to use advanced processes such as hot runner, gas assisted molding, cylinder, etc. purchase Rack CNC punching machine In general, whether the machine tool has a blank holder mechanism, or even a side lubricant, multi station progressive, etc., should be considered for large stamping dies. The climbing frame punching machine should not only focus on product design, but also ignore the service life of the mold.

In the past, the traditional punching machine usually used manual or semi-automatic punching to finish punching the workpiece. Now, with the continuous progress of punching machine technology, some shortcomings of the former manual punching machine itself are more and more obvious, Jiangsu Rack CNC punching machine Which one is good The speed is very slow, so the efficiency is very low. If it is semi-automatic, automatic feeding cannot be carried out. CNC climbing frame punching machine needs frequent maintenance to ensure its life; Before operation, check whether the punch and die of the numerical control punching machine are matched, otherwise the punching machine host will be damaged. When assembling the upper and lower moulds, the models of the upper and lower moulds must be the same, and the fixing sleeve of the upper mould must be tightened. purchase Rack CNC punching machine When placing the lower die, pay attention to the upward direction of the knife edge (the end with a small aperture), and do not damage the machine by installing it. Do not remove the quick coupler when the system has working pressure during operation. The screw rod and nut shall be lubricated with oil.

With the continuous development of China's manufacturing industry, the technical level of punching machines and other equipment is required to be higher and higher. The requirements of the market for equipment determine that punching machine manufacturers should constantly improve the technical level of their products. Rack punching machine manufacturers should follow the market development and produce high-end punching equipment, Jiangsu purchase Rack CNC punching machine With the help of the intelligent trend of the development of China's machine tool industry, the punching machine technology is brought to a higher level. In addition, Rack CNC punching machine When punching, after the mold is installed, insert the pipe for punching. It is strictly prohibited to empty punch when there is no pipe, otherwise the mold will be damaged. When punching the full hole, if there is no punching, it will automatically return. Please move the lower proximity switch downward to protect the mold.