The lubrication function of the pipe punching machine will be gradually weakened after long-term use, which will lead to increased friction and damage in the process of equipment operation. Even professional pipe punching machines are not immune, Anhui CNC punching machine Therefore, in order to avoid this kind of situation, it is necessary to add lubricant in time, especially the position of the punch to maintain lubrication, reduce friction and extend the service life of the equipment. The pipe punching machine is the most taboo to be impacted by foreign objects. Even if the impact degree is not large, component failure is likely to occur. CNC punching machine manufactor Therefore, whether before or after use, check whether there is any foreign matter between the punch and the lower die, and use carefully to prevent the punch from being damaged due to the extrusion of the punch and the lower die caused by foreign matters.

The automatic punching manipulator is a kind of equipment specially developed to realize automatic punching unmanned production based on automatic equipment and according to the characteristics of punching production. Anhui CNC punching machine It can replace manual punching, handling, loading and unloading of materials at each punching station, and improve the working efficiency of the whole production line. The automatic punching manipulator can be used in processing industries with high repetition, danger and rhythm, such as punching, CNC punching machine manufactor It is an important embodiment of the spirit of "pioneering and innovating" in modern chemical industrialization in terms of saving labor costs, improving labor and equipment safety, and maintaining product capacity, quality, process stability, etc. The press manipulator can be connected by multiple single press manipulators to form a press production line, which will better improve production efficiency.

In the past, the traditional punching machine usually used manual or semi-automatic punching to finish punching the workpiece. Now, with the continuous progress of punching machine technology, some shortcomings of the former manual punching machine itself are more and more obvious, Anhui CNC punching machine manufactor The speed is very slow, so the efficiency is very low. If it is semi-automatic, automatic feeding cannot be carried out. CNC climbing frame punching machine needs frequent maintenance to ensure its life; Before operation, check whether the punch and die of the numerical control punching machine are matched, otherwise the punching machine host will be damaged. When assembling the upper and lower moulds, the models of the upper and lower moulds must be the same, and the fixing sleeve of the upper mould must be tightened. major CNC punching machine When placing the lower die, pay attention to the upward direction of the knife edge (the end with a small aperture), and do not damage the machine by installing it. Do not remove the quick coupler when the system has working pressure during operation. The screw rod and nut shall be lubricated with oil.

For CNC punching machine equipment, quality is the hard truth for enterprises to survive. Therefore, we must ensure the stability of product quality. Equipment and materials of CNC punching machine; Due to the increased cost of current materials, Anhui CNC punching machine manufactor Some enterprises will start with raw materials and choose inferior materials to replace them. The result is that the product quality is not guaranteed. Before using the automatic CNC punching machine, be sure to check whether there are sundries at the punch and the lower die edge. Add lubricating oil to the upper and lower moving parts of the punch. CNC punching machine During use, keep the oiling part of the numerical control punching machine free of oil shortage. At the same time, it should be noted that after the use of the NC punching machine is completed, the NC punching machine should be cleaned first, and the punch should be pressed down to the low position to better protect the NC punching machine.

Energy saving and environmental protection, less noise, faster working efficiency than ordinary punches, small footprint, safe and secure operation. Anhui CNC punching machine manufactor The punching needle is specially designed, and the time for changing the mold is short. Time delay protection circuit. When nobody operates the machine, the time delay protection switch will automatically enter the standby state. If you want to start work, you need to turn on the circuit switch again. The punching machine for handrail shelf of guardrail stairs is widely used in punching stainless steel, aluminum alloy bathroom, color steel, zinc steel guardrails, and is the equipment with fast pipe punching processing at present. Guardrail stair handrail punching machine can be customized to multiple working positions, easy and convenient to disassemble the mold, durable mold, easy for novices to use and so on. CNC punching machine It can debug and punch half hole or full hole at will, with flat punching and accurate positioning. It can also produce various new anti-theft nets (diamond anti-theft net, round tube square tube anti-theft net, door flower, etc.), and provide one-year warranty service for the whole machine.

The climbing frame punching machine is mainly used for punching operations in industrial processing and manufacturing. Because different processing materials need to be punched in the industrial processing and manufacturing fields and in the building materials industry, Anhui CNC punching machine manufactor Choosing a high-quality square tube punching machine can effectively improve the overall processing efficiency in the processing field. People should pay attention to the regular maintenance and cleaning of the square tube punching machine when using it. Since there are more or less oil stains and sundries left on the surface of the machine after each use, CNC punching machine In order to better maintain the normal operation of the equipment, it is not only necessary to clean the equipment every day for oil stains and sundries, but also to regularly overhaul the key parts of the equipment with abnormal looseness at intervals.