The insufficient strength of the punching machine for zinc steel guardrail is the direct cause of the fracture or excessive residual deformation of the parts in work. Taiyuan Rack CNC punching machine Which one is good The strength of parts is divided into volume strength and surface contact strength. For example, if the stress produced by the pipe punching machine parts under the load is within a large volume, the strength of the parts under this stress state is called volume strength (strength for short). Rack CNC punching machine If two parts change from point contact or line contact to small surface contact before and after being loaded, and their surfaces produce large local stress (called contact stress), then the strength of the parts is called surface contact strength (called contact strength for short).

Use the numerical control zinc steel fence punching machine. The equipment is accurate and fast, with excellent product effect, simple and convenient operation and long service life, Taiyuan purchase Rack CNC punching machine It is the best choice for pipe punching. However, no matter how good the machine is, it also needs to pay attention to daily maintenance in order to make it perform to a large extent. The working fluid shall be replaced once a year, and the replacement time shall not exceed three months. Rack CNC punching machine Which one is good The sliding block shall be filled with lubricating oil frequently, the exposed surface of the column shall be kept clean frequently, and oil shall be sprayed before each work. If the machine is out of service for a long time, the surface should be cleaned and coated with antirust oil. The pressure gauge shall be calibrated and checked every six months.

Once the high-end CNC punching machine breaks down, its working efficiency will be seriously affected. If it is improperly operated, it will also have a more fatal impact on the life of the equipment. purchase Rack CNC punching machine Which one is good Using the rack punching machine in strict accordance with the standard can not only improve the efficiency, but also extend the service life. Determine whether your equipment is multi station or single station, and talk about the multi station punching machine, Taiyuan Rack CNC punching machine When in use, only one oil circuit switch can be opened for operation at a time, and multiple oil circuit switches cannot be opened at the same time. Many people will use multiple switches simultaneously to improve efficiency, which will have a bad impact on equipment operation and processing quality.

The main function of the piercing head of the numerical control punching machine is to punch the position where stainless steel and other materials need to be punched, so its position must be adjusted accurately. When debugging, pay attention to, Taiyuan purchase Rack CNC punching machine In the measuring range, when the center of the pendulum is at a low point, the tip of the piercing head should be at the horizontal position of the rotation axis of the pendulum. Remove the sample splint with heavy weight, adjust the pointer to the place with large value, then place the numerical control punching machine at the position where the test starts and press the release button to let the pendulum swing, Rack CNC punching machine Under normal circumstances, the pointer should be at the zero point. If not, use the zero adjustment screw to adjust. If it is necessary to replace heavy lumps with different weights during use, the zero point shall be re adjusted.

In order to give better play to the performance of the pipe punching machine, what matters should be paid attention to when the pipe punching machine is used and when it is maintained later? The oil of the pipe punching machine needs to be replaced regularly, basically every year, Taiyuan purchase Rack CNC punching machine It should take less than three months, that is to say, it needs to be replaced within three months. Check whether there is any problem with the protective safety device, lubrication and other parts, and whether the relevant fastening screws are firm and loose. Rack CNC punching machine Which one is good When the mechanical operation is over, cut off the power supply and wipe the machine tool. In short, special attention should be paid to the daily use of the pipe punching machine, and regular inspection and maintenance should be carried out to ensure that the pipe punching machine can operate efficiently and normally.

When debugging the pointer friction force of the numerical control punching machine, first place the pointer at the zero point, and then place it at the test position, purchase Rack CNC punching machine Then let the pendulum swing by releasing the button, which means that the pointer should not exceed the zero point. If it exceeds the zero point, it is necessary to inject lubricating oil into the pointer bearing or release the spring pressure of the pointer to debug it. The purpose of debugging the professional CNC punching machine is to ensure that the punching machine can have better punching quality and precision, so we carefully debug the punching machine that has just been purchased or replaced with more important parts, Rack CNC punching machine Which one is good In this way, the ideal punching effect can be obtained. At the same time, accurate debugging is also an effective protection for the service life of the NC punching machine itself.