Roller servo feeder, mountain type clamp feeder, hydraulic punching machine, servo feed square and rectangular pipe punching machine, CNC automatic punching machine for profiles is a new type of automatic processing equipment, which can process half holes or full holes on square pipes, round pipes and special-shaped pipes of different materials, Henan Climbing frame CNC punching machine By changing the mold, it can also process various sizes and shapes of hole diameters, and can process guardrails, door flowers, shelves and other pipes, which are widely used in modern processing industry. Low cost. The cutting tool of the NC profile automatic punching machine consumes less energy, and the automatic operation saves a lot of manpower, and the pipe processing cost is greatly reduced. NC automatic punching machine for profiles is one of the advanced automatic punching equipment in the industry at present, Climbing frame CNC punching machine manufactor It has many functions, high precision and low cost, which has brought great convenience to pipe processing, and is actually an important contributor to modern processing industry.

In order to enable the square pipe punching machine to effectively achieve a sound punching effect, the punching of the equipment should be checked regularly, major Climbing frame CNC punching machine And ensure that there is no aging in the mold to prevent the punching effect of processed objects from being affected. In order to make the square pipe punching machine have a better punching effect and extend its service life, Climbing frame CNC punching machine manufactor During the use, adequate maintenance and overhaul shall be carried out, and the greasy dirt and other dirt on the equipment shall be cleaned timely after each punching operation.

The insufficient strength of the punching machine for zinc steel guardrail is the direct cause of the fracture or excessive residual deformation of the parts in work. Henan Climbing frame CNC punching machine manufactor The strength of parts is divided into volume strength and surface contact strength. For example, if the stress produced by the pipe punching machine parts under the load is within a large volume, the strength of the parts under this stress state is called volume strength (strength for short). Climbing frame CNC punching machine If two parts change from point contact or line contact to small surface contact before and after being loaded, and their surfaces produce large local stress (called contact stress), then the strength of the parts is called surface contact strength (called contact strength for short).

The lubrication function of the pipe punching machine will be gradually weakened after long-term use, which will lead to increased friction and damage in the process of equipment operation. Even professional pipe punching machines are not immune, Henan Climbing frame CNC punching machine Therefore, in order to avoid this kind of situation, it is necessary to add lubricant in time, especially the position of the punch to maintain lubrication, reduce friction and extend the service life of the equipment. The pipe punching machine is the most taboo to be impacted by foreign objects. Even if the impact degree is not large, component failure is likely to occur. Climbing frame CNC punching machine manufactor Therefore, whether before or after use, check whether there is any foreign matter between the punch and the lower die, and use carefully to prevent the punch from being damaged due to the extrusion of the punch and the lower die caused by foreign matters.

When punching with the climbing frame punching machine, the die shall be installed and inserted into the pipe for punching. It is strictly prohibited to empty punch when there is no pipe, otherwise the die will be damaged, Henan Climbing frame CNC punching machine When punching full holes, if there is no punching, it will automatically return. Please move the lower proximity switch downward to protect the mold. In addition, it should be noted that the CNC climbing frame punching machine needs inspection and maintenance after running for a period of time. Check whether the blade of the punching needle has been passivated. If it has been passivated, please remove the punching needle and grind it, or purchase a new punching needle from the climbing frame punching machine manufacturer. In winter, the temperature becomes low. To protect the equipment, Climbing frame CNC punching machine manufactor If necessary, the engine should be started up and run idle for a period of time to warm up; If the equipment operates for a long time, check the temperature of the equipment. The temperature of the hydraulic oil should be controlled between 30 and 60 ℃.

In order to ensure the flexibility of the pipe punching machine, Henan Climbing frame CNC punching machine manufactor The sliding block also needs to be often injected with lubricating oil. Generally, before the pipe punching machine runs, it needs to be injected with oil. The column surface of the pipe punching machine also needs to be clean. If the pipe punching machine has not been used for a long time Henan Climbing frame CNC punching machine The surface shall be cleaned and coated with antirust oil to avoid corrosion and rust. The pipe punching machine should also be checked regularly, and the pressure gauge should be checked once every 6 months.