上海龙凤1314

Welcome to the official website of Foshan Jinhai CNC Machinery Co., Ltd!

 WeChat pictures_ 20210420135910.png

 Rack punching machine
Your current location: home page > Hot information

Which one is better to purchase full-automatic punching machine in Anhui

2022-07-16
 Which one is better to purchase full-automatic punching machine in Anhui

The maintenance of the hydraulic rack punching machine can greatly delay the reduction of the accuracy of the hydraulic punching machine and extend its service life. The reduction of hydraulic punching machine precision is mainly manifested in the wear and plastic deformation of punching machine parts. Anhui Full automatic punching machine Which one is good Therefore, the lack of maintenance is one of the reasons why the accuracy of the NC punching machine is reduced. You can combine your own situation to see whether this is the reason for the reduction in accuracy. The movement relationship (time and movement) between components is damaged due to grinding and deformation of components, purchase Full automatic punching machine It will also reduce the accuracy of the hydraulic rack punching machine. Numerous practical experiences have proved that the accuracy of hydraulic punching machines without maintenance or improper maintenance can reduce much faster than that of well maintained hydraulic punching machines.

 Which one is better to purchase full-automatic punching machine in Anhui

The ordinary pipe punching machine has no automatic positioning system, which is equivalent to a small punching machine that solves the feeding problem. Automatic pipe punching machine adds automatic positioning system on the basis of ordinary pipe punching machine, Anhui Full automatic punching machine Which one is good It greatly improves the precision and speed of punching, which can be understood as an automatic controlled high-precision small punch. The automatic pipe punching machine can not only position itself, but also automatically feed materials in batches, greatly saving manpower. The hydraulic automatic pipe punching machine produced by our factory adopts large torque AC synchronous servo motor, Full automatic punching machine It is characterized by fast response, high positioning accuracy, low noise, small brake heat loss and long service life. Motion control: professional PLC controller, touch screen operation, simple and convenient.

 Which one is better to purchase full-automatic punching machine in Anhui

Once the high-end CNC punching machine breaks down, its working efficiency will be seriously affected. If it is improperly operated, it will also have a more fatal impact on the life of the equipment. purchase Full automatic punching machine Which one is good Using the rack punching machine in strict accordance with the standard can not only improve the efficiency, but also extend the service life. Determine whether your equipment is multi station or single station, and talk about the multi station punching machine, Anhui Full automatic punching machine When in use, only one oil circuit switch can be opened for operation at a time, and multiple oil circuit switches cannot be opened at the same time. Many people will use multiple switches simultaneously to improve efficiency, which will have a bad impact on equipment operation and processing quality.

 Which one is better to purchase full-automatic punching machine in Anhui

During commissioning, it is not necessary to feed materials, but it is necessary to first raise the guide screw on the guide plate, and then gradually adjust the ram of the punch to the bottom dead center by inching. It is necessary to pay special attention to that the guide plate should not press the floating rod too low, otherwise the floating rod will be bent or broken. purchase Full automatic punching machine Which one is good When starting the punching machine for continuous punching, it is necessary to rotate the speed adjusting screw of the nc servo feeder clockwise. The slider moves slightly slowly, so that it can be seen whether the slider touches the nylon gasket and the length adjusting screw when it moves back and forth. Full automatic punching machine If the full-automatic punching machine only touches the length adjusting screw but not the nylon gasket when the sliding block moves back and forth, it is because the floating rod is lowered too deep, and the guide screw on the punching machine needs to be gradually raised.

 Which one is better to purchase full-automatic punching machine in Anhui

In order to ensure that the round pipe punching machine has good quality and use effect, it is recommended that enterprises choose genuine hydraulic oil with relatively high cost performance. Because the hydraulic oil with good brand has high purity and less impurities, it will not be worn by impurities after being used for the round pipe punching machine, and the oil is not easy to deteriorate, Anhui Full automatic punching machine Can play a better role. As the hydraulic system is an important part of the pipe punching machine, and the hydraulic oil plays a crucial role in it, purchase Full automatic punching machine When using the round pipe punching machine, enterprises should not only use the equipment according to the operating rules, but also pay attention to adding and replacing the hydraulic oil in the hydraulic system regularly to ensure that the quality and life of the round pipe punching machine will not be affected.

 Which one is better to purchase full-automatic punching machine in Anhui

Science and technology bring convenience to people, improve work efficiency and increase income. The CNC climbing frame punching machine is a fast punching equipment independently developed by Jinhai, which can be used for punching C-shaped steel, square steel and channel steel. Anhui Full automatic punching machine Which one is good It is widely used in mining, tunnel, construction engineering and other fields. Compared with the same type of products on the market, Full automatic punching machine This product improves the punching precision and speed, and is suitable for two feed servo motors, imported hydraulic oil pump, contact phone of climbing frame automatic punching machine, PLC operating system, and can also match a variety of molds, achieving a true sense of "multi-function". The CNC climbing frame full-automatic punching machine works better together with the special die produced by Yinjiang, bringing infinite convenience to new and old users.

 Zinc steel guardrail punching machine

 1.png Mobile: 13679829857

 3.png Email: [email protected]

 4.png Address: Workshop 2, Baishaqiao Second Industrial Zone, Shishan, Nanhai District, Foshan City





Main business area: Guangdong Guangzhou Foshan Shenzhen Dongguan Zhongshan Zhuhai Huizhou Wuhan Shanghai