First, observe the safety operation regulations of the numerical control punching machine. When the punching equipment is in place, the chassis should be leveled and stabilized. The punching frame should be vertical, and grounding protection should be done according to the construction power requirements. secondly, Zhejiang Full automatic punching machine Which one is good Before starting work, carefully check whether each component is properly configured and whether the fastening part is loose. If there is any abnormality, timely and correctly handle it. Numerically controlled punching machines are usually equipped with a variety of protective devices, Full automatic punching machine Before starting operation, make sure that these protective devices can work normally, which can improve the safety protection performance of the NC punching machine during operation and effectively reduce the accident rate during operation. In addition, the operator shall wear all kinds of armor as required, clean up the sundries on the machine table and within a certain range around, and irrelevant personnel shall not be close to the working area when the punching machine is running.

The automatic punching machine has beautiful appearance, reasonable and simple structure, and is easy to operate, Zhejiang Full automatic punching machine Which one is good In this way, the cost of training staff can be saved, and the accuracy of the automatic punching machine is high. The climbing frame automatic punching machine agent is not easy to make mistakes, purchase Full automatic punching machine Even the most rigorous operation can be completed accurately. The operation screen of the automatic punching machine is a 7-inch touch screen, which is convenient for operation. The automatic punching machine adopts hydraulic and mechanical structure, with stable physical performance and strong adaptability.

Once the pipe rack punching machine contacts the water source, it is easy for the machine to break down, so the enterprise should ensure that the equipment can stay away from the water source and maintain a dry environment. If the water ingress at the solenoid valve is more serious, Zhejiang purchase Full automatic punching machine Parts may rust and cannot be used normally. Besides, the moist substances in the air will also damage the system elements, so it is necessary to ensure that the compressed air of the equipment is always dry. Only in this way can we effectively avoid machine failures and increase maintenance costs, and give full play to the advantages of high accuracy and efficiency of equipment. When using the pipe punching machine, the enterprise should also let the staff carefully check the equipment parts exposed to the air. Full automatic punching machine Once any abnormality is found, the operation should be stopped, and the operation should be restarted after troubleshooting. This can effectively protect the equipment from damage and extend its life to provide quality services for enterprises.

Pay attention to the operating condition of the equipment when starting the square pipe punching machine, Zhejiang Full automatic punching machine In case of abnormal noise and displacement, the square tube punching machine shall be shut down in time, and fault diagnosis and maintenance shall be carried out. Since the clamping and separating action of the pneumatic part of the professional square pipe punching machine requires high flexibility, purchase Full automatic punching machine When in use, not only should the pneumatic part be checked regularly to see whether it can be sucked and pulled freely, but also should pay attention to whether there is air leakage in the square tube punching machine.

Drilling is the process of drilling holes on the processing materials with a drill bit, while the pipe punching machine is the process of punching holes under the drill bit by gravity. Automatic pipe punching machine is suitable for processing soft materials, Zhejiang Full automatic punching machine Because the holes drilled by the drilling machine will have burrs and unevenness. The drilling machine is suitable for processing hard materials, because the punching force of the pipe punching machine often causes cracks in the processing materials. Full automatic punching machine Which one is good The processing objects of punching machine and pipe punching machine are similar to a large extent. The punching machine is divided into ordinary punching machine, rapid punching machine, etc. Since the punching machine needs a feeding system, its volume is generally large. The automatic pipe punching machine is a further development of the punch, which solves the problem that the punch needs an independent feeding system, so it is small in size.

Use the numerical control zinc steel fence punching machine. The equipment is accurate and fast, with excellent product effect, simple and convenient operation and long service life, Zhejiang purchase Full automatic punching machine It is the best choice for pipe punching. However, no matter how good the machine is, it also needs to pay attention to daily maintenance in order to make it perform to a large extent. The working fluid shall be replaced once a year, and the replacement time shall not exceed three months. Full automatic punching machine Which one is good The sliding block shall be filled with lubricating oil frequently, the exposed surface of the column shall be kept clean frequently, and oil shall be sprayed before each work. If the machine is out of service for a long time, the surface should be cleaned and coated with antirust oil. The pressure gauge shall be calibrated and checked every six months.